manualshive.com logo in svg

NEC MuPD78F0132H, User Manual

The NEC MuPD78F0132H product user manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and guidelines on operating and troubleshooting the product. With a user-friendly interface, users can easily access this invaluable resource to maximize their product experience.

Share
Download
background image

CHAPTER  6   16-BIT  TIMER/EVENT  COUNTERS  00  AND  01 

User’s Manual  U16899EJ2V0UD 

140 

Table 6-2.  CR00n Capture Trigger and Valid Edges of TI00n and TI01n Pins 

(1)  TI00n pin valid edge selected as capture trigger (CRC0n1 = 1, CRC0n0 = 1) 

TI00n Pin Valid Edge 

CR00n Capture Trigger 

 ES0n1 

ES0n0 

Falling edge 

Rising edge 

0 

1 

Rising edge 

Falling edge 

0 

0 

No capture operation 

Both rising and falling edges 

1 

1 

 

(2)  TI01n pin valid edge selected as capture trigger (CRC0n1 = 0, CRC0n0 = 1) 

TI01n Pin Valid Edge 

CR00n Capture Trigger 

 ES1n1 

ES1n0 

Falling edge 

Falling edge 

0 

0 

Rising edge 

Rising edge 

0 

1 

Both rising and falling edges 

Both rising and falling edges 

1 

1 

Remarks 1.  Setting ES0n1, ES0n0 = 1, 0 and ES1n1, ES1n0 = 1, 0 is prohibited. 

 2. 

ES0n1, ES0n0: 

Bits 5 and 4 of prescaler mode register 0n (PRM0n) 

 

 

ES1n1, ES1n0: 

Bits 7 and 6 of prescaler mode register 0n (PRM0n) 

 

 

CRC0n1, CRC0n0:  Bits 1 and 0 of capture/compare control register 0n (CRC0n) 

 3.  n = 0: 

µ

PD78F0132H 

 

 

n = 0, 1: 

µ

PD78F0133H, 78F0134H, 78F0136H, 78F0138H, 78F0138HD 

 

Cautions  1.  Set a value other than 0000H in CR00n in the mode in which clear & start occurs on a match 

of TM0n and CR00n.   

 

2.  If CR00n is cleared to 0000H in the free-running mode and in the clear mode using the valid 

edge of the TI00n pin, an interrupt request (INTTM00n) is generated when the value of 

CR00n changes from 0000H to 0001H following TM0n overflow (FFFFH).  In addition, 

INTTM00n is generated after a match between TM0n and CR00n, after detecting the valid 

edge of the TI01n pin, or the timer is cleared by a one-shot trigger. 

 

3.  When the valid edge of the TI01n pin is used, P01 or P06 cannot be used as the timer output 

pin (TO0n).  When P01 or P06 is used as the TO0n pin, the valid edge of the TI01n pin 

cannot be used. 

 

4.  When CR00n is used as a capture register, read data is undefined if the register read time 

and capture trigger input conflict (the capture data itself is the correct value).  If a timer 

count stop and a capture trigger input conflict, the captured data is undefined. 

 

5.  Do not rewrite CR00n during TM0n operation. 

 

Summary of Contents for MuPD78F0132H





























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MuPD78F0132H

Häfele 633.03.298 Operating Instructions Manual preview
633.03.298
Brand: Häfele Pages: 24
KIPI ecoMAX360P1-C Installation And Operating Manual preview
ecoMAX360P1-C
Brand: KIPI Pages: 44
H3C WX1804H Configuration Manual preview
WX1804H
Brand: H3C Pages: 11
Nanjing Putian Datang Information Electronics Co., Ltd. CL12/2410LI-A User Manual preview
CL12/2410LI-A
Brand: Nanjing Putian Datang Information Electronics Co., Ltd. Pages: 2
DUNIWAY Stockroom Terranova 960 Instruction Manual preview
Terranova 960
Brand: DUNIWAY Stockroom Pages: 30
Grundfos EC 15 Installation And Operating Instructions Manual preview
EC 15
Brand: Grundfos Pages: 80
Pixsys ATR226 User Manual preview
ATR226
Brand: Pixsys Pages: 24
Advanced Control Technologies th104 Installation Instructions preview
th104
Brand: Advanced Control Technologies Pages: 3
aldes 611242-FC Installation Manual preview
611242-FC
Brand: aldes Pages: 3
Dawn CONTROL-1500A Manual preview
CONTROL-1500A
Brand: Dawn Pages: 100
HIMA HIMatrix F31 02 Manual preview
HIMatrix F31 02
Brand: HIMA Pages: 48
Licht-Technik Mix4-6 Functional Description preview
Mix4-6
Brand: Licht-Technik Pages: 13
Geco GH10HA User Manual preview
GH10HA
Brand: Geco Pages: 20
Parker Porter MPC Series Installation, Programming, & User Manual preview
Porter MPC Series
Brand: Parker Pages: 30
PPA Citrox CX-4512 Instruction Manual preview
Citrox CX-4512
Brand: PPA Pages: 2
Virtualfly TQ6+ User Manual preview
TQ6+
Brand: Virtualfly Pages: 5
Scaime eNod4-C BOX Manual preview
eNod4-C BOX
Brand: Scaime Pages: 74
GAC 103 Series Quick Start Manual preview
103 Series
Brand: GAC Pages: 5

Brands by name

Popular brands

Load more brands