manualshive.com logo in svg

NEC MuPD70F3187, User Manual

The NEC MuPD70F3187 is a premium electronics device designed to enhance your user experience. With this innovative product, you can enjoy an array of advanced features and functionalities. To explore the full potential of this device, we provide a comprehensive user manual for free download at manualshive.com. Unleash its capabilities today!

Share
Download
background image

735

Chapter 17

Clocked Serial Interface 3 (CSI3)

User’s Manual U16580EE3V1UD00

<1>  When the CSICAEn bit of the CSIM3n register is set to 1, operating clock supply is enabled.
<2>  Specify the transfer mode by setting the CSIC3n and CSIL3n registers.
<3>  Write 1 to the FPCLRn bit of the SFA3n register to clear all the CSIBUFn pointers to 0.
<4>  Confirm that the SFFULn bit = 0, SFEMPn bit = 1, and SFPn3 to SFPn0 bits = 0000 in the SFA3n

register.

<5>  Specify the transfer mode by using the TRMDn, DIRn, CSITn, CSWEn, and CSMDn bits of the

CSIM3n register and, at the same time, enable reception by setting the CRXEn bit to 1.

<6>  Set the number of data to be received by using the SFNn3 to SFNn0 bits of the SFN3n register.
<7>  Write dummy transfer data to the SFDB3n register (reception start trigger). Writing dummy data

exceeding the set value of the SFN3n register is prohibited.
Since the chip select outputs (SCS3n0 to SCS3n3) are ineffective in the slave mode and always
output the inactive level, writing of CS data to the SFCS3n register is not necessary.

<8>  Confirm that the INTC3n interrupt has occurred and the SFEMPn bit is 1. Then read the SIRB3n

register (sequentially read the receive data stored in the CSIBUFn register).

<9>  Write 1 to the FPCLRn bit of the SFA3n register, and clear all the CSIBUFn pointers to 0 in 

preparation for the next transfer.

<10> Confirm that the SFFULn bit = 0, SFEMPn bit = 1, and SFPn3 to SFPn0 bits = 0000 in the SFA3n

register.

<11> Disable reception by clearing the CRXEn bit of the CSIM3n register to 0 (end of reception).

Remarks: 1. 

To execute a further transfer, repeat <6> to <10> before <11>. 
Perform writing dummy transfer data in <7> every time transfer is executed.

2. 

The SO3n pin output is fixed to low level (default value).

3. 

μ

PD70F3187:

n = 0, 1

μ

PD70F3447:

n = 0

Summary of Contents for MuPD70F3187






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MuPD70F3187

Parker 890CS Product Manual preview
890CS
Brand: Parker Pages: 478
Taconova NOVASTAT EL DIGITAL Manual preview
NOVASTAT EL DIGITAL
Brand: Taconova Pages: 7
Casambi RP GROUP Mounting Instructions preview
RP GROUP
Brand: Casambi Pages: 2
KIPI ecoMAX360P1-C Installation And Operating Manual preview
ecoMAX360P1-C
Brand: KIPI Pages: 44
Altronix Trove T1VK3F4 Installation Manual preview
Trove T1VK3F4
Brand: Altronix Pages: 8
nvent JBS-100-EC Installation Instructions Manual preview
JBS-100-EC
Brand: nvent Pages: 6
Teledyne THCD-401 Instruction Manual preview
THCD-401
Brand: Teledyne Pages: 47
Western Co WMarine10 Technical Manual preview
WMarine10
Brand: Western Co Pages: 14
Nuvoton NuMicro M252 Series User Manual preview
NuMicro M252 Series
Brand: Nuvoton Pages: 38
Watts WFHC 06Z 02 HC RF 24 User Manual preview
WFHC 06Z 02 HC RF 24
Brand: Watts Pages: 18
Texas Instruments Errata MSP430F6779 Manual preview
Errata MSP430F6779
Brand: Texas Instruments Pages: 27
KBR multicomp F144-MS-1V1C1TI6RO-3 User Manual preview
multicomp F144-MS-1V1C1TI6RO-3
Brand: KBR Pages: 68
Carrier 40BNC Installation Instructions preview
40BNC
Brand: Carrier Pages: 4
Haiwell S04AI User Manual & Application Case preview
S04AI
Brand: Haiwell Pages: 18
Badger Meter MDS 2000 User Manual preview
MDS 2000
Brand: Badger Meter Pages: 66
CAME BIANCA-VC Installation Manual preview
BIANCA-VC
Brand: CAME Pages: 32
JLCooper Electronics SloMoPro User Manual preview
SloMoPro
Brand: JLCooper Electronics Pages: 11
Texas Instruments TIDA-00830 Quick Start Manual preview
TIDA-00830
Brand: Texas Instruments Pages: 6

Brands by name

Popular brands

Load more brands