NEC mPD780973 Series Preliminary User'S Manual Download

Page: 58 / 301

CHAPTER 3 CPU ARCHITECTURE

3.4 Operand Address Addressing

The following methods are available to specify the register and memory (addressing) which undergo manipulation

during instruction execution.

3.4.1 Implied addressing

[Function]

The register which functions as an accumulator (A and AX) in the general register is automatically (implicitly)

addressed.

Of the

PD780973 Subseries instruction words, the following instructions employ implied addressing.

Instruction

MULU

DIVUW

ADJBA/ADJBS

ROR4/ROL4

[Operand format]

Because implied addressing can be automatically employed with an instruction, no particular operand format is

necessary.

[Description example]

In the case of MULU X

With an 8-bit

8-bit multiply instruction, the product of A register and X register is stored in AX. In this example,

the A and AX registers are specified by implied addressing.

Summary of Contents for mPD780973 Series














































































































































































































































































































Search results

Summary of Contents for mPD780973 Series

Reviews:

Related manuals for mPD780973 Series

Brands by name

Popular brands

NEC mPD780973 Series, Preliminary User'S Manual

Search results

Summary of Contents for mPD780973 Series

Reviews:

Related manuals for mPD780973 Series

Brands by name

Popular brands