manualshive.com logo in svg

NEC mPD780973 Series, Preliminary User'S Manual

The NEC mPD780973 Series is an advanced electronic device that offers state-of-the-art functionalities. Enhance your experience with this cutting-edge product by accessing the Preliminary User's Manual for free. Simply download the manual from our website and explore the vast array of features this versatile product has to offer.

Share
Download
background image

129

CHAPTER  9   8-BIT  TIMER/EVENT  COUNTERS  2,  3  TM2,  TM3

9.4.4  8-bit PWM output operation

8-bit timer/event counters operate as PWM output when bit 6 (TMCn6) of 8-bit timer mode control register n (TMCn)

is set to 1.

The duty rate pulse determined by the value set to 8-bit compare register n (CRn) is output from TIOn.

Set the active level width of PWM pulse to CRn, and the active level can be selected with bit 1 (TMCn1) of TMCn.

Count clock can be selected with bit 0 to bit 2 (TCLn0 to TCLn2) of timer clock select register n (TCLn).

PWM output enable/disable can be selected with bit 0 (TOEn) of TMCn.

Caution

Rewrite of CRn in PWM mode is allowed only once in a cycle.

Remark

n = 2, 3

(1) PWM output basic operation

[Setting]

<1>

Set port latch (P43, P44) and port mode register 4 (PM43, PM44) to 0.

<2>

Set active level width with 8-bit compare register (CRn).

<3>

Select count clock with timer clock select register n (TCLn).

<4>

Set active level with bit 1 (TMCn1) of TMCn.

<5>

Count operation starts when bit 7 (TCEn) of TMCn is set to 1.

Set TCEn to 0 to stop count operation.

[PWM output operation]

<1>

PWM output (output from TIOn) outputs inactive level after count operation starts until overflow is

generated.

<2>

When overflow is generated, the active level set in <1> of setting is output.

The active level is output until CRn matches the count value of 8-bit counter n (TMn).

<3>

After the CRn matches the count value, PWM output outputs the inactive level again until overflow is

generated.

<4>

PWM output operation <2> and <3> are repeated until the count operation stops.

<5>

When the count operation is stopped with TCEn = 0, PWM output changes to inactive level.

Remark  n = 2, 3

Summary of Contents for mPD780973 Series














































































































































































































































































































Reviews:

No comments

Related manuals for mPD780973 Series

Y-Solar Smart-MPPT Li Series User Manual preview
Smart-MPPT Li Series
Brand: Y-Solar Pages: 6
Wavetec Spectra Installation Manual preview
Spectra
Brand: Wavetec Pages: 17
Calsense ET1 Manual To Programming preview
ET1
Brand: Calsense Pages: 9
MaestroHome Smart Controller Quick Setup Manual preview
Smart Controller
Brand: MaestroHome Pages: 10
Samsung DMS2.5 Service Manual preview
DMS2.5
Brand: Samsung Pages: 32
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Brand: Parker Pages: 44
Samson 3277 Quick Manual preview
3277
Brand: Samson Pages: 2
Cadac 343 User Instructions preview
343
Brand: Cadac Pages: 4
Riello 20120499 Manual preview
20120499
Brand: Riello Pages: 72
OMEGA AIR AWS-C Instructions Manual preview
AWS-C
Brand: OMEGA AIR Pages: 12
Linear Technology LTC4232 Demo Manual preview
LTC4232
Brand: Linear Technology Pages: 6
Altera Stratix III Using Manual preview
Stratix III
Brand: Altera Pages: 59
Danfoss AFD 2 VFG 221 Operating Manual preview
AFD 2 VFG 221
Brand: Danfoss Pages: 8
Dawn CONTROL-1500A Manual preview
CONTROL-1500A
Brand: Dawn Pages: 100
3M Touch Screen Controller RX151 Reference Manual preview
Touch Screen Controller RX151
Brand: 3M Pages: 31
Delta Electronics Programmable Logic Controller DVP28SV Instruction Sheet preview
Programmable Logic Controller DVP28SV
Brand: Delta Electronics Pages: 2
London Electronics INTUITIVE-I Manual preview
INTUITIVE-I
Brand: London Electronics Pages: 23
Viessmann 5268 Servocontrol Manual preview
5268 Servocontrol
Brand: Viessmann Pages: 4

Brands by name

Popular brands

Load more brands