manualshive.com logo in svg

NEC mPD780973 Series, Preliminary User'S Manual

The NEC mPD780973 Series is an advanced electronic device that offers state-of-the-art functionalities. Enhance your experience with this cutting-edge product by accessing the Preliminary User's Manual for free. Simply download the manual from our website and explore the vast array of features this versatile product has to offer.

Share
Download
background image

51

CHAPTER  3   CPU  ARCHITECTURE

3.2.3  Special function registers (SFRs)

Unlike the general registers, these registers have special functions.

They are allocated in the FF00H to FFFFH area.

The special-function registers can be manipulated like the general registers, with the operation, transfer and bit

manipulation instructions.  The bit units (1, 8, or 16 bits) for the manipulation vary for each register.

Each manipulation bit unit can be specified as follows.

• 1-bit manipulation

Describe the symbol reserved with assembler for the 1-bit manipulation instruction operand (sfr.bit).

This manipulation can also be specified with an address.

• 8-bit manipulation

Describe the symbol reserved with assembler for the 8-bit manipulation instruction operand (sfr).

This manipulation can also be specified with an address.

• 16-bit manipulation

Describe the symbol reserved with assembler for the 16-bit manipulation instruction operand (sfrp).

When addressing an address, describe an even address.

Table 3-5 gives a list of special-function registers.  The meaning of items in the table is as follows.

• Symbol

Symbol indicating the address of a special function register. It is a reserved word in the RA78K/0, and is defined

via the header file “sfrbit.h” in the CC78K/0.  It can be described as an instruction operand when the RA78K/

0 and ID78K0 are used.

• R/W

Indicates whether the corresponding special-function register can be read or written.

R/W :  Read/write enable

R

:  Read only

W

:  Write only

• Manipulatable bit units

Indicates the manipulatable bit unit (1, 8, or 16). “—” indicates a bit unit for which manipulation is not possible.

• After reset

Indicates each register status upon RESET input.

Summary of Contents for mPD780973 Series














































































































































































































































































































Reviews:

No comments

Related manuals for mPD780973 Series

Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Brand: Parker Pages: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Brand: Parker Pages: 26
Vageo DT-1 Manual preview
DT-1
Brand: Vageo Pages: 2
Eaton Cutler-Hammer Jockey Instructions Manual preview
Cutler-Hammer Jockey
Brand: Eaton Pages: 12
Desoutter 6159326760 Original Instructions Manual preview
6159326760
Brand: Desoutter Pages: 74
Jandy AquaLink RS All Button Quick Review Card preview
AquaLink RS All Button
Brand: Jandy Pages: 2
elero BoxControl Compact Instruction Manual preview
BoxControl Compact
Brand: elero Pages: 8
Taconova Tacosol Load EXA L Manual preview
Tacosol Load EXA L
Brand: Taconova Pages: 40
Oilon VMi 6-17 Installation And Operation Manual preview
VMi 6-17
Brand: Oilon Pages: 74
Oilon VSi 6-14 Installation And Operation Manual preview
VSi 6-14
Brand: Oilon Pages: 74
ATN Thermal Entry Wizard Manual preview
Thermal Entry Wizard
Brand: ATN Pages: 56
Watt Stopper DRD6 v2 Installation Instructions preview
DRD6 v2
Brand: Watt Stopper Pages: 3
FDI SYG-S7G2-43C-MDK User Manual preview
SYG-S7G2-43C-MDK
Brand: FDI Pages: 28
Cypress Semiconductor CYUSBS232 Quick Start Manual preview
CYUSBS232
Brand: Cypress Semiconductor Pages: 2
Danfoss Optyma Plus OP-MPS Instructions Manual preview
Optyma Plus OP-MPS
Brand: Danfoss Pages: 86
Pololu DRV8824 User Manual preview
DRV8824
Brand: Pololu Pages: 9
Armacost Lighting Proline 713420 Quick Start Manual preview
Proline 713420
Brand: Armacost Lighting Pages: 2
YASKAWA UUX001686 Installation Manual preview
UUX001686
Brand: YASKAWA Pages: 18

Brands by name

Popular brands

Load more brands