NEC mPD780973 Series Preliminary User'S Manual Download Page 44

Page: 44 / 301

CHAPTER 3 CPU ARCHITECTURE

(2) CALLT instruction table area

The 64-byte area 0040H to 007FH can store the subroutine entry address of a 1-byte call instruction (CALLT).

(3) CALLF instruction entry area

The area 0800H to 0FFFH can perform a direct subroutine call with a 2-byte call instruction (CALLF).

3.1.2 Internal data memory space

The

PD780973 Subseries have the following RAM.

(1) Internal high-speed RAM

Table 3-3. Internal High-Speed RAM Capacity

Product

Internal High-Speed RAM

PD780973(A)

768

8 bits (FC00H to FEFFH)

PD78F0974

1024

8 bits (FB00H to FEFFH)

The 32-byte area FEE0H to FEFFH is allocated with four general-purpose register banks composed of eight 8-

bit registers.

The internal high-speed RAM can be used as stack memory.

(2) LCD display RAM

An LCD display RAM is allocated to a 20

4 bits area consisting of FA59H to FA6CH. The LCD display RAM

can also be used as a normal RAM.

3.1.3 Special function register (SFR) area

An on-chip peripheral hardware special-function register (SFR) is allocated in the area FF00H to FFFFH (Refer

to 3.2.3 Special function registers (SFRs) Table 3-5 Special Function Register List).

Caution Do not access addresses where the SFR is not assigned.

Summary of Contents for mPD780973 Series














































































































































































































































































































Search results

Summary of Contents for mPD780973 Series

Reviews:

Related manuals for mPD780973 Series

Brands by name

Popular brands

NEC mPD780973 Series, Preliminary User'S Manual

Search results

Summary of Contents for mPD780973 Series

Reviews:

Related manuals for mPD780973 Series

Brands by name

Popular brands