manualshive.com logo in svg

NEC 78K0/KD1 Series, User Manual

The NEC 78K0/KD1 Series, a cutting-edge product in the electronics domain, offers unparalleled performance and efficiency. Explore its limitless potential with the comprehensive User Manual that you can easily download for free from our website. Elevate your experience and delve into the world of NEC 78K0/KD1 Series with our helpful manual.

Share
Download
background image

Preliminary User’s Manual  U16315EJ1V0UD

343

CHAPTER  18   STANDBY  FUNCTION

18.1  Standby Function and Configuration

18.1.1  Standby function

Table 18-1.  Relationship Between HALT Mode, STOP Mode, and Clock

X1 Input Clock

Ring-OSC Clock

Subsystem Clock

CPU Clock

HALT mode

Oscillation continues

Oscillation continues

Oscillation continues

Operation stopped

STOP mode

Oscillation stopped

Oscillation continues

Oscillation continues

Operation stopped

The standby function is designed to reduce the power consumption of the system.  The following two modes are

available.

(1) HALT mode

HALT instruction execution sets the HALT mode.  In the HALT mode, the CPU operation clock is stopped, but the

system clock oscillator continues oscillating.  In this mode, power consumption is not decreased as much as in

the STOP mode, but the HALT mode is effective for restarting operation immediately upon interrupt request

generation and carrying out intermittent operations.

(2) STOP mode

STOP instruction execution sets the STOP mode.  In the STOP mode, the X1 input clock oscillator stops,

stopping the whole system, thereby considerably reducing the CPU power consumption.

Because this mode can be cleared by an interrupt request, it enables intermittent operations to be carried out.

However, because a wait time is required to secure the oscillation stabilization time after the STOP mode is

released, select the HALT mode if it is necessary to start processing immediately upon interrupt request

generation.

In either of these two modes, all the contents of registers, flags and data memory just before the standby mode is

set are held.  The I/O port output latches and output buffer statuses are also held.

Cautions 1. STOP mode can be used only when operating on the X1 input clock or Ring-OSC clock.

HALT mode can be used when operating on the X1 input clock, Ring-OSC clock, or

subsystem clock.  However, when the STOP instruction is executed during Ring-OSC clock

operation, the X1 oscillator stops, but Ring-OSC oscillator does not stop.

2. When shifting to the STOP mode, be sure to stop the peripheral hardware operation before

executing STOP instruction.

3. The following sequence is recommended for power consumption reduction of the A/D

converter when the standby function is used: First clear bit 7 (ADCS) of the A/D converter

mode register (ADM) to 0 to stop the A/D conversion operation, and then execute the HALT or

STOP instruction.

4. Ring-OSC clock oscillation cannot be stopped in the STOP mode.  However, when the Ring-

OSC clock is used as the CPU clock, the CPU operation is stopped for 17/f

R

 (s) after STOP

mode is released.

Summary of Contents for 78K0/KD1 Series






























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 78K0/KD1 Series

Aalborg DPC Operating Manual preview
DPC
Brand: Aalborg Pages: 128
SOMFY Situo 1 RTS Manual preview
Situo 1 RTS
Brand: SOMFY Pages: 4
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Brand: Ros Pages: 10
Cardin Elettronica S486 Series Installation And Reference preview
S486 Series
Brand: Cardin Elettronica Pages: 56
Nuvoton NuMicro M252 Series User Manual preview
NuMicro M252 Series
Brand: Nuvoton Pages: 38
Phoenix Contact 2297031 Manual preview
2297031
Brand: Phoenix Contact Pages: 56
AC Tech SCF SERIES Quick Reference Manual preview
SCF SERIES
Brand: AC Tech Pages: 2
V-TAC VT-2472 Manual preview
VT-2472
Brand: V-TAC Pages: 2
J+J J2 L/H 10 Manual preview
J2 L/H 10
Brand: J+J Pages: 56
Shimaden SR80 Series Instruction Manual preview
SR80 Series
Brand: Shimaden Pages: 16
LEGRAND MRD6 v2 Installation Instructions Manual preview
MRD6 v2
Brand: LEGRAND Pages: 10
Lumel re72 series Quick Start Manual preview
re72 series
Brand: Lumel Pages: 32
Holars AS H-TAG User Manual preview
H-TAG
Brand: Holars AS Pages: 15
LevelOne WAB-8011 Quick Installation Manual preview
WAB-8011
Brand: LevelOne Pages: 11
Sierra Wireless 1400897-I User Manual preview
1400897-I
Brand: Sierra Wireless Pages: 58
Astrapool LumiPlus Quick Start Manual preview
LumiPlus
Brand: Astrapool Pages: 2
OptoSupply OS-OC013AIG2 Product Manual preview
OS-OC013AIG2
Brand: OptoSupply Pages: 4
Smartgen HEM4000 User Manual preview
HEM4000
Brand: Smartgen Pages: 46

Brands by name

Popular brands

Load more brands