Naviter Oudie 3, User Manual

Page: 87 / 136

Settings 83
© 2003 - 2013 ... Naviter d.o.o.
. Magnetic bearing to target (MagBrg) = Magnetic course to fly to get to the target
. Track over ground (Trk) = Direction of the flight (true)
. Magnetic Track over ground (MagTrk) = Current magnetic course of flight
. Radial (Radial) = Magnetic direction from the waypoint to the current position
. Speed over ground (GS) = Groundspeed. This value is negative if the difference between heading
and track is more than 90 degrees
.
Local time (Time) = UTC time from GPS corrected by time zone set in the Units dialog
. Arrival time (ETA) = Estimated time of arrival to the selected waypoint
. Estimated time enroute (ETE) = Estimated time to go to selected waypoint
. Nearest airport (Near Apt) = Name of the nearest airport. Tapping on this navbox opens airport
properties dialog
.
Inverted Distance to target (DisInv) = Distance to selected target in inverted units as currently
selected units. If your units are kilometers, this distance will be in nautical miles
.
Dist to TP (DistTP) = Distance to the wayponit
. Distance to OZ (DistOZ) = Distance to the selected Observation Zone
. Steering course to last thermal (ToLT) = Difference in degrees between Bearing to last thermal
and Track over ground
.
Dist to last thermal (DisLT) = Distance to the last thermal
. GPS Status (GPS) = It displays the status of the GPS signal. It can be either NODATA, BAD, OK, 2D,
3D/x
.
Battery info (Bat) = Displays battery status. It can be either Full, Chrg (Charging), Ext (External) or a
percentage value of the battery status
.
Distance from takeoff (dToff) = distance from your position to the Takeoff
Altitude navboxes:
. Altitude QNH (Alt) = Altitude above sea level
. Flight level (FL) = Altitude above standard atmosphere pressure
. Height AGL (Agl) = Altitude above the ground elevation vertically below the glider position
. Altitude m QNH (Alt m) = Altitude in meters QNH regardless of the units you are currently using
. Altitude ft QNH (Alt ft) = Altitude in feet QNH regardless of the units you are currently using
. Ground elevation (Gnd) = Terrain elevation vertically below the glider position
. GPS Altitude = GPS altitude
. Arrival altitude (Arrival) = Expected Arrival altitude at the selected waypoint calculated by taking the
distance, MC, wind, glider polar, bugs and ballast into account. It is corrected for reserve altitude.
"Arrival altitude" will be positive when the glider is above the calculated glide slope, and negative when it
is below the calculated glide slope.
.
Required Altitude (ReqAlt) = Estimated altitude loss from current position to target taking into accout
current MC, bugs, ballast and wind settings
.
Task arrival altitude (tArr) = Altitude required to complete the task
Final glide navboxes:
. Flown L/D (Cur.L/D) = Current glide ratio estimated over the last two minutes of flight
. Required L/D (Req. L/D) = Required glide ratio to reach the selected waypoint
. Thermal L/D (Ther. L/D) = Glide ratio since last circling phase finished
. Arrival altitude (Arrival) = Expected Arrival altitude at the selected waypoint calculated by taking the
distance, MC, wind, glider polar, bugs and ballast into account. It is
.
Required Altitude (ReqAlt) = Estimated altitude loss from current position to target taking into accout
current MC, bugs, ballast and wind settings
.
Required Mc (Req.Mc) = MacCready ring setting which will allow you to final glide exactly to the
Target. It shows Arrival Altitude when Arrival altitude for MC=0 is less than zero
.
Task required L/D (tL/D) = Required glide ration to complete the task
Speed navboxes:
92