NanoPhotometer C40 User Manual Download

Page: 14 / 133

NanoPhotometer

NP80/N60/N50/C40

User Guide Version 3.1

CCESSORIES

TANDARD

CCESSORIES



Connecting Cable

USB connecting cable to connect the NanoPhotometer

to a computer to control the

NanoPhotometer

via computer (please see page 23 Software Installation).



NanoPhotometer

Power Adapter

Power adapter for the NanoPhotometer

and for charging the optional built-in battery pack.

Note:

Use only the power adapter supplied with your instrument or a replacement part from the

manufacturer or your supplier.



Dust Cover

PTIONAL

CCESSORIES



Didymium Glass Filter (C40/NP80)

The certified didymium glass filter can be used to verify the
wavelength and photometric accuracy of the NanoPhotometer

cuvette applications.

Summary of Contents for C40






































































































































Search results

Summary of Contents for C40

Reviews:

Related manuals for C40

Brands by name

Popular brands

NanoPhotometer C40, User Manual

Search results

Summary of Contents for C40

Reviews:

Related manuals for C40

Brands by name

Popular brands