NAL RESEARCH CORPORATION A3LA-RG General Description Manual Download | Manualshive

Page: 57 / 119

background image

NAL Research Corporation (451-93156-009A)

57

and <sri> indicates the SBD ring indication status:

0

No SBD ring alert received

1

SBD ring alert received

Note: It is valid for the A3LA-R/RM/RGS to receive a telephony ring alert and an SBD ring alert

at the same time. Assertion of the RI signal indicates only the presence of an alert; this
command may be used to determine the type(s) of ring alert.

A.8.96 +CSQ[F] – Signal Quality

Exec Command: +CSQ[F]
Execution command returns the received signal strength indication <rssi> from the A3LA-RG.
Response is in the form:

+CSQ: <rssi>

where <rssi> is:

0

Equivalent to 0 bars displayed on the signal strength indicator

1

Equivalent to 1 bar displayed on the signal strength indicator

2

Equivalent to 2 bars displayed on the signal strength indicator

3

Equivalent to 3 bars displayed on the signal strength indicator

4

Equivalent to 4 bars displayed on the signal strength indicator

5

Equivalent to 5 bars displayed on the signal strength indicator

Note: The +CSQ form of the command waits for an updated signal strength reading to become
available. This will usually be within two seconds of issuing the command. If the A3LA-RG is in

the process of acquiring the system, or in a satellite handoff, a delay in response of up to 10
seconds may be experienced.

If the A3LA-RG has no SIM, is awaiting a SIM PIN entry, has an invalid SIM, or has otherwise
not proceeded to successful registration, the delay in response may exceed the 50 second
timeout limit. Under such condition, an ERROR response will be received. To avoid a delayed
response due to registration problems, issue the +CREG command to verify registration prior to
entering the +CSQ command to obtain signal strength.

Note: The +CSQF form of the command returns immediately, reporting the last known signal
strength.

Test Command: +CSQ=?
List the supported signal strength indications. The response is in the form:

+CSQ: (supported <rssi>s)

A.8.97 +CULK – Unlock

Exec Command: +CULK=<unlock key>
Unlock the SBD functionality of the A3LA-RG after it has been locked by the Gateway. The

unlock key must be obtained by contacting Iridium’s customer support.
<unlock key>:

0000000000000000 .. FFFFFFFFFFFFFFFF (a string of 16 hexadecimal digits)

«
...
55
56
57
58
59
...
»

Summary of Contents for A3LA-RG
























































































































Reviews:

No comments

Related manuals for A3LA-RG

Vantage Connect

Brand: DAVIS Pages: 12

Brand: SEA Pages: 2

Brand: ActionTec Pages: 2

Brand: Easlink Pages: 13

Brand: NAL Pages: 158

Alpha GMT 125 Series

Brand: EnerSys Pages: 26

Brand: Tenda Pages: 52

Brand: Tenada Pages: 9

Dolphin Navigan Wireless Commissioner NWC 300

Brand: EnOcean Pages: 9

Brand: ComBlock Pages: 22

FRITZ!WLAN USB Stick

Brand: Fritz! Pages: 51

Brand: Garnet Pages: 22

DG834PN - RangeMax ADSL Modem Wireless Router

Brand: NETGEAR Pages: 108

Brand: Zte Pages: 24

Brand: CalAmp Pages: 63

Brand: Dantel Pages: 8

Brand: Abocom Pages: 14

Brand: ICT Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands