NAL RESEARCH CORPORATION A3LA-RG General Description Manual Download Page 37 | Manualshive

Page: 37 / 119

background image

NAL Research Corporation (451-93156-009A)

37



If the password required is SIM PUK, then <newpin> is required, where <newpin> is

the new SIM Card PIN to replace the old SIM Card PIN.



If the password required is SIM PUK2, then <newpin> is required, where <newpin> is
the new SIM Card PIN2 to replace the old SIM Card PIN2



Both <pin> and <newpin> should be of string type enclosed by “ “; for example,
”1234”.

Read Command: +CPIN?

Read command returns an alphanumeric string indicating whether some password is required or
not. Response is in the form:

+CPIN: <code>

where <code> can be one of the following:

READY

A3LA-RG is not waiting for any password.

PH PIN

A3LA-RG is waiting for Phone Unlock Code to be given.

SIM PIN

A3LA-RG is waiting for SIM Card PIN1 Code to be given.

SIM PUK

A3LA-RG is waiting for SIM PUK to be given (because SIM PIN1 is blocked).

SIM PIN2

A3LA-RG is waiting for SIM PIN2 to be given.*

SIM PUK2

A3LA-RG is waiting for SIM PUK2 to be given (because SIM PIN2 is
blocked).

*Note: The response “SIM PIN2” is somewhat misleading, because it indicates one of three
possible scenarios:

1.

PIN1 has already been successfully entered (thus equivalent to the READY
response).

2.

No PIN1 is required (thus equivalent to the READY response).

3.

The A3LA-RG is waiting for PIN2 (used to access Fixed Dialing settings and other
subscription-based features).

In any of these three cases, the A3LA-RG should be available to place and receive calls.

Note: +CPIN is closely related to +CLCK and +CPWD. See these commands for additional

information.

A.8.49 +CPMS – Select Preferred SMS Message Storage

Set Command: +CPMS=<mem1>[, <mem2>[,<mem3>]]
Set command selects memory storages <mem1>, <mem2> and <mem3>. <mem1> is the
memory from which messages are read and deleted; <mem2> is the memory to which writing
and sending operations are made; <mem3> is the memory to which received SMS messages

are to be stored. If a chosen storage is not appropriate for the A3LA-RG, final result code +CMS
ERROR: <cms_err> is returned.

Valid values for <mem1>, <mem2> and <mem3> are:

"SM" SIM message storage

Response is in the form:

+CPMS: <used1>,<total1>,<used2>,<total2>,<used3>,<total3>

«
...
35
36
37
38
39
...
»

Summary of Contents for A3LA-RG
























































































































Reviews:

No comments

Related manuals for A3LA-RG

Brand: Campbell Pages: 3

Sierra Wireless AirLink RV50

Brand: Campbell Pages: 2

Brand: Sierra Wireless Pages: 12

Brand: NetComm Pages: 20

Brand: Ebyte Pages: 22

Brand: jablotron Pages: 4

Brand: T-Home Pages: 168

MultiConnect Cell 100 Series MTC-EV3

Brand: Multitech Pages: 30

Brand: Ovation Pages: 19

Brand: Honeywell Pages: 87

Brand: MikroTik Pages: 3

Brand: Scientific Atlanta Pages: 92

Brand: DeVilbiss Pages: 38

HomePortal 1500CW

Brand: 2Wire Pages: 78

Brand: Davicom Pages: 24

Brand: Enfora Pages: 23

Brand: Cooper Bussmann Pages: 109

Brand: 3Com Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands