NAL RESEARCH CORPORATION A3LA-RG General Description Manual Download Page 97

Page: 97 / 119

NAL Research Corporation (451-93156-009A)

APPENDIX D: INFORMATIVE EXAMPLES

The examples below are presented in two different formats. The format used in each example has no

significance. A single format will be used in a future revision of this document.

D.1 Unit Identification

When beginning to build a communication link, a general DTE application controlling the A3LA-RG

should confirm the type of Iridium device to which it is connected.

D.2 Setting the Default Configuration

The DTE sets the A3LA-RG’ default configuration to no flow control, SBD automatic notifications enabled.

D.3 Power-on to Sending an SBD Message

The DTE will power up the A3LA-RG, wait for the A3LA-RG to acquire the network, and send a 70-byte

message.

To A3LA-RG

(from DTE)

To DTE (from A3LA-RG)

Description

AT+CGMI

Get manufacturer name

Iridium

AT+CGMM

Get model number

AT+CGMR

Get revision

Call processor version: <revision>

DSP version: <revision>

…

AT+CGSN

Get IMEI

300001000000000

To A3LA-RG

(from DTE)

To DTE (from A3LA-RG)

Description

AT&K0

Disable RTS/CTS flow control

AT+SBDMTA=1

Enable SBD ring indications

AT&W0

Store the configuration as profile 0

AT&Y0

Select profile 0 as the power-up

default

Summary of Contents for A3LA-RG
























































































































Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands

NAL RESEARCH CORPORATION A3LA-RG, General Description Manual

Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands