NAL RESEARCH CORPORATION A3LA-RG General Description Manual Download Page 49 | Manualshive

Page: 49 / 119

background image

NAL Research Corporation (451-93156-009A)

49

<type>: if the number starts with a ‘+’, then the type is 145; otherwise the type is 129

Note: MSISDN numbers are only available if they were intentionally stored on the SIM.

A.8.79 +CSSSC – Supplementary Services Short Code

Exec Command: +CSSSC=”<shortcode>”

Execute the given shortcode. If the shortcode fails, a CME ERROR code is returned. Otherwise,
OK is returned.

Note: Shortcode functionality is only available if provisioned.

Note: This command does not support command concatenation.

A.8.80 +WIRLP – Iridium Radio Link Protocol

Set Command:

+WIRLP=[<ver>[,<k1>[,<k2>[,<t1>[,<n2>[,<t2>[,<r1>[,<r2>[,<t4>[,<mode>]]]
]]]]]]]

Set desired IRLP parameters to be negotiated with the peer at the start of the next data call.
Note that these desired parameters are reset to hardcoded defaults at the end of a data call, so
this command should be issued while a call is not in progress.

<ver> specifies the desired IRLP version and can take the following values:

0

Default IRLP version (N0)

<k1> represents the maximum number of sequentially numbered I frames that may be
outstanding at any given time at downlink direction (IWF->A3LA-RG) and can take the following
values:

1-105. Default is 105.

<k2> represents the maximum number of sequentially numbered I frames that may be
outstanding at any given time at uplink direction (A3LA-RG->IWF) and can take the following
values:

1-105. Default is 105.

<t1> is used to supervise the acknowledgment of transmitted unnumbered frames. The values
are defined to be the earliest instant to enter the recovery procedure and can take on the

following values:

27-255 (in 50-ms unit). Default is 30.

<n2> is used to represent the maximum number of re-transmission attempts of a frame (e.g.
I,S,N,U frame) and can take on the following values:

1-255. Default is 15.

<t2> is used to indicate the amount of time available within which the acknowledging frame
must be transmitted and can take on the following values:

1-255 (in 10-ms unit). Default is 10.

<r1> is used to represent the maximum number of S frames that are used to acknowledge I
frames at downlink direction (IWF->A3LA-RG) and can take on the following values:

«
...
47
48
49
50
51
...
»

Summary of Contents for A3LA-RG
























































































































Reviews:

No comments

Related manuals for A3LA-RG

Brand: T-Mobile Pages: 10

Brand: WePresent Pages: 71

Brand: Clear Pages: 2

Brand: AVM Pages: 51

DIVA T/A ISDN Modem

Brand: Eicon Networks Pages: 146

Brand: Four-Faith Pages: 33

Brand: GridConnect Pages: 17

Brand: Genesis Pages: 3

Brand: Archtek Pages: 38

Brand: 3Jtech Pages: 50

HughesNet HT1-00 Series

Brand: Hughes Pages: 2

Brand: Observa Telecom Pages: 28

Brand: TRENDnet Pages: 2

Brand: TRENDnet Pages: 3

Brand: Radyne Pages: 237

Brand: Quasar Pages: 7

DSL-100D - 8 Mbps DSL Modem

Brand: D-Link Pages: 8

Brand: Kathrein Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands