NAL RESEARCH CORPORATION A3LA-RG General Description Manual Download Page 51

Page: 51 / 119

NAL Research Corporation (451-93156-009A)

Select DCE mode of operation.

<tm> can take the following values:

IRLP test mode off (default)

IRLP test mode on

Read Command: +WTM?
Query the current parameter setting. The response is in the form:

+WTM: <tm>

Test Command: +WTM=?
List the supported parameter settings. The response is in the form:

+WTM: (supported <tm>s)

A.8.83 +WDLDM – IRLP Dynamic Link Delay Measurement

Set Command: +WDLDM=[<dldm>[,<mi>[,<dtl>]]]

Set the DCE dynamic link delay measurement parameters.
<dldm> can take the following values:

measurement off (default)

measurement on

<mi> denotes the measurement interval and can take the following values:

1-255 (in 1000-ms unit). Default is 15 for 15000 ms.

<dtl> denotes the delay tolerance in the link delay difference and can take the following values:

1-100 (in 1% unit). Default is 10%.

Read Command: +WDLDM?

Query the current parameter settings. The response is in the form:

+WDLDM: <dldm>,<mi>,<dtl>

Test Command: +WDLDM=?
List the supported parameter settings. The response is in the form:

+WDLDM: (supported <dldm>s), (supported <mi>s), (supported <dtl>s)

A.8.84 +WDAV – Register or Deregister an RS232 DAV Data Peripheral

Set Command: +WDAV=[<DP type>[,<encrypt>]]
Register or deregister an RS232 DAV Data Peripheral (DP).
<DP type> can take on the following values:

Deregister peripheral

<encrypt> can take on the following values:

Encryption is not supported at this time

Read Command: +WDAV?

Query the current DP registration parameter settings. The response is in the form:

+WDAV:<DP type>,<encrypt>

Test Command: +WDAV=?

Summary of Contents for A3LA-RG
























































































































Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands

NAL RESEARCH CORPORATION A3LA-RG, General Description Manual

Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands