NAL RESEARCH CORPORATION A3LA-RG General Description Manual Download

Page: 99 / 119

NAL Research Corporation (451-93156-009A)

D.6 SBD Automatic Notification Automatic Registration

The DTE verifies its registration state and enables automatic registration using the “Ask” mode.

D.7 Originating a Data Call

An example of how to make a data call is given below:

D.8 Answering a Data Call

The A3LA-RG is capable of accepting mobile terminated data calls. The following is a sequence of

commands that can be used to establish the connection.

+SBDRING

A3LA-RG indicates an incoming message.
The RI line also toggles.

AT+SBDIXA

DTE initiates an SBD session in answer to

the automatic notification

+SBDIXA:0,23,1,237,90,2

A3LA-RG informs DTE that a 90-byte

message was successfully received with

MTMSN 237, and that two further MT

messages are queued at the GSS

AT+SBDRB

DTE retrieves the received message from

the A3LA-RG

To A3LA-RG

(from DTE)

To DTE (from A3LA-RG)

Description

AT+SBDREG?

Query the A3LA-RG registration status

+SBDREG: 2

A3LA-RG is registered

AT+SBDAREG=2

DTE sets the automatic registration to

“Ask” mode

…

A3LA-RG is moved

+AREG: 0, 0

A3LA-RG notifies DTE that it needs to

AT+SBDREG

DTE instructs the A3LA-RG to register

+SBDREG: 2, 0

Registration is successful

To A3LA-RG

(from DTE)

To DTE (from A3LA-RG)

Description

AT+CBST=6,0,1

Asynchronous modem 4800 bps and IRLP

AT+CR=1

Enable reporting

ATD1234567890

Dial remote modem

+CR: REL ASYNC

Call connected at DTE rate of 9600

CONNECT ASYNC 9600

Summary of Contents for A3LA-RG
























































































































Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands

NAL RESEARCH CORPORATION A3LA-RG, General Description Manual

Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands