NAL RESEARCH CORPORATION A3LA-RG General Description Manual Download Page 17

Page: 17 / 119

NAL Research Corporation (451-93156-009A)

is no response it power cycles the 9523. This can be enabled or disabled with the ^MPTDC command.

Registrations Every 23 Hours: The micro-controller will force manual registration by implementing the

command AT+COPS=1 every 23 hours to make sure the 9523 stays registered. Registration will not occur
during a data/voice call. This can be enabled or disabled with the ^MPTFR command.

Forced Power Cycles Every 24 Hours: The micro-controller will force a power cycle of the 9523 board

every 24 hours. Power cycle will not happen during a data/voice call. This can be enabled or disabled with
the ^MPTFP command.

13.0 MOUNTING RECOMMENDATIONS

The A3LA-RG has four features on its bottom surface that can aid in its mounting (see Appendix J).

These four features are pre-drilled at a minimum depth of 0.25 inch to accept 6-32 thread type.

14.0 TECHNICAL SUPPORT

FOR TECHNICAL SUPPORT, PLEASE CONTACT US AT

Phone: 703-392-1136

FAX: 703-392-6795

E-mail:

[email protected]

Technical documents are also available to download on NAL Research’s website

www.nalresearch.com

Summary of Contents for A3LA-RG
























































































































Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands

NAL RESEARCH CORPORATION A3LA-RG, General Description Manual

Search results

Summary of Contents for A3LA-RG

Reviews:

Related manuals for A3LA-RG

Brands by name

Popular brands