manualshive.com logo in svg

MTU MS150112/01E, Operating Instructions Manual

Share
Download
MTU MS150112/01E Operating Instructions Manual Download Page 66

351 – AL Open Load Cylinder B1

ZKP-Number: 1.8004.550

Injector wiring fault, cylinder B1
Yellow alarm – misfiring

Cause

Corrective action

Disruption fault in injector
wiring, cylinder B1.

1. Check injector wiring and solenoid valve.
2. Contact Service.

352 – AL Open Load Cylinder B2

ZKP-Number: 1.8004.551

Injector wiring fault, cylinder B2
Yellow alarm – misfiring

Cause

Corrective action

Disruption fault in injector
wiring, cylinder B2.

1. Check injector wiring and solenoid valve.
2. Contact Service.

353 – AL Open Load Cylinder B3

ZKP-Number: 1.8004.552

Injector wiring fault, cylinder B3
Yellow alarm – misfiring

Cause

Corrective action

Disruption fault in injector
wiring, cylinder B3.

1. Check injector wiring and solenoid valve.
2. Contact Service.

354 – AL Open Load Cylinder B4

ZKP-Number: 1.8004.553

Injector wiring fault, cylinder B4
Yellow alarm – misfiring

Cause

Corrective action

Disruption fault in injector
wiring, cylinder B4.

1. Check injector wiring and solenoid valve.
2. Contact Service.

355 – AL Open Load Cylinder B5

ZKP-Number: 1.8004.554

Injector wiring fault, cylinder B5
Yellow alarm – misfiring

Cause

Corrective action

Disruption fault in injector
wiring, cylinder B5.

1. Check injector wiring and solenoid valve.
2. Contact Service.

66 | Troubleshooting | MS150112/01E 2014-10

TIM-ID: 0000029153 - 005

Summary of Contents for MS150112/01E























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands