manualshive.com logo in svg

MTU MS150112/01E, Operating Instructions Manual

Share
Download
MTU MS150112/01E Operating Instructions Manual Download Page 124

7.9.2 Additional fuel filter – Replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Filter wrench

F30379104

1

Engine oil
Easy-change filter

(→ Spare Parts Catalog)

4

WARNING

Fuels are combustible.

Risk of fire and explosion!

• Avoid open flames, electrical sparks and ignition sources.
• Do not smoke.

Supplementary fuel filter – Re-
placement

1.

Remove easy-change filter (2) with filter
wrench.

2.

Clean sealing surface on filter head (1).

3.

Coat seal on easy-change filter (2) slightly
with engine oil (arrow).

4.

Screw on easy-change filter (2) by hand un-
til the seal makes contact with the filter
head and tighten manually.

5.

Replace further easy-change filters in the
same way.

6.

Vent fuel system (→ Page 122)

124 | Task Description | MS150112/01E 2014-10

TIM-ID: 0000029800 - 002

Summary of Contents for MS150112/01E























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands