manualshive.com logo in svg

MTU MS150112/01E, Operating Instructions Manual

Share
Download
MTU MS150112/01E Operating Instructions Manual Download Page 183

7.19.2 Battery-charging generator drive – Drive belt tension adjustment

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 60-320 Nm

F30452768

1

Ratchet

F30027341

1

Torque wrench, 10-60 Nm

F30452769

1

Ratchet

F30027340

1

WARNING

Spring/circlip/tensioning roller preload.

Risk of injury!

• Only use specified tool and equipment.

Adjusting belt tension

1.

Remove protective cover.

2.

Slacken screws (1) and (2) by half a turn.

Result:

Belt tensioner moves against the drive belt
and tensions it.

3.

Tighten screw (2) with torque wrench to the specified tightening torque.

Name

Size

Type

Lubricant

Value/Standard

Screw

M10

Tightening torque

60 Nm +5 Nm

4.

Tighten screw (1) with torque wrench to the specified tightening torque.

Name

Size

Type

Lubricant

Value/Standard

Screw

M10

Tightening torque

42 Nm

5.

Install protective cover.

MS150112/01E 2014-10

| Task Description | 183

TIM-ID: 0000000945 - 007

Summary of Contents for MS150112/01E























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands