manualshive.com logo in svg

MTU MS150112/01E, Operating Instructions Manual

Share
Download
MTU MS150112/01E Operating Instructions Manual Download Page 4

7.12.7 Exhaust flaps – Checking coupling rods

operability and play

147

7.12.8 Exhaust flaps – Coupling rod replacement

149

7.13 Starting Equipment

152

7.13.1 Starter – Condition check

152

7.14 Lube Oil System, Lube Oil Circuit

153

7.14.1 Engine oil level – Check at sight glass

153

7.14.2 Engine oil – Level check with oil dipstick

154

7.14.3 Engine oil – Change

155

7.14.4 Engine oil – Sample extraction and analysis

157

7.15 Oil Filtration / Cooling

158

7.15.1 Engine oil filter – Replacement

158

7.15.2 Centrifugal oil filter – Cleaning and filter-

sleeve replacement

160

7.16 Coolant Circuit, General, High-Temperature

Circuit

162

7.16.1 Engine coolant – Level check

162

7.16.2 Engine coolant – Change

163

7.16.3 Engine coolant – Draining

164

7.16.4 Exhaust flaps – Draining coolant from

servomotors

166

7.16.5 Engine coolant – Filling

167

7.16.6 Engine coolant pump – Relief bore check

170

7.16.7 Engine coolant – Sample extraction and

analysis

171

7.17 Low-Temperature Circuit

172

7.17.1 Charge-air coolant – Level check

172

7.17.2 Charge-air coolant – Change

173

7.17.3 Charge-air coolant – Draining

174

7.17.4 Charge-air coolant – Filling

177

7.17.5 Checking charge-air coolant pump pressure

relief port

180

7.18 Belt Drive

181

7.18.1 Drive belt – Condition check

181

7.19 Battery-Charging Generator

182

7.19.1 Checking battery-charging generator

182

7.19.2 Battery-charging generator drive – Drive belt

tension adjustment

183

7.19.3 Battery-charging generator drive – Drive belt

replacement

184

7.20 Fan Drive

185

7.20.1 Fan drive – Drive belt check / adjustment

185

7.20.2 Fan drive – Drive belt replacement

187

7.21 Engine Mounting / Support

188

7.21.1 Engine mounting – Check

188

7.22 Wiring (General) for Engine/Gearbox/Unit

189

7.22.1 Еngine cabling ‒ Check

189

7.23 Accessories for (Electronic) Engine

Governor / Control System

190

7.23.1 Resetting CDC parameter and entering IIG

with DiaSys®

190

7.23.2 Actuators – Visual inspection and test

191

7.23.3 Engine governor and connectors – Cleaning

193

7.23.4 Engine governor plug connections – Check

194

7.23.5 NOx sensor – Replacement

195

7.23.6 Lambda sensor – Replacement

197

8 Appendix A

8.1 Abbreviations

199

8.2 MTU contact persons/service partners

202

9 Appendix B

9.1 Special Tools

203

9.2 Index

212

4 | Table of Contents | MS150112/01E 2014-10

DCL-ID: 0000029808 - 003

Summary of Contents for MS150112/01E























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands