manualshive.com logo in svg

MTU MS150112/01E, Operating Instructions Manual

Share
Download
MTU MS150112/01E Operating Instructions Manual Download Page 158

7.15 Oil Filtration / Cooling

7.15.1 Engine oil filter – Replacement

Preconditions

☑

Run engine to reach operating temperature.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Filter wrench

F30379104

Engine oil
Oil filter

(→ Spare Parts Catalog)

Sealing ring

(→ Spare Parts Catalog)

WARNING

Hot oil.
Oil can contain combustion residues which are harmful to health.

Risk of injury and poisoning!

• Wear protective clothing, gloves, and goggles / safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Engine oil filter – Replacement

1.

Stop engine and disable engine start.

2.

After warning up and directly stopping the
engine, open the vent plug (1) on the oil
heat exchanger.

3.

Wait 5 minutes until the oil system is vent-
ed and the oil has drained off.

Note:

Always use a new sealing ring for the vent plug.

4.

Screw the vent plug (1) back in.

Name

Size

Type

Lubricant

Value/Standard

Screw

M14

Tightening torque

(Engine oil)

35 Nm +4 Nm

158 | Task Description | MS150112/01E 2014-10

TIM-ID: 0000028834 - 005

Summary of Contents for MS150112/01E























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands