![background image](http://html.mh-extra.com/html/moulinex/me41513e/me41513e_manual_1840196007.webp)
corresponding notches in the body
A1
.
Position the ring F2 on the kebbe making head, then screw the nut A5 tight.
Place the head thus assembled on the motor unit as indicated in diagram 2.
Note: this attachment is used without screen or cutter.
SAUSAGE FILLER TUBE (G)
This attachment, which fits to the mincer head, enables you to produce all sorts of sausages that you can season to
your own taste.
Fitting (diagram 4)
Insert the feed screw
A2
into the body
A1
of the mincer head
A
. Position the filler tube
G
, then the nut
A5
, and
tighten firmly. Place the head thus assembled on the motor unit
E
as indicated in diagram 2.
Note: this attachment is used without screen or cutter.
Use:
Important
: this attachment should only be used after you have minced the meat, added the seasoning and thoroughly
mixed the filling.
After having soaked the sausage skin in lukewarm water to make it supple, thread it onto the filler tube
G
, leaving 5 cm
at the end (which you close by making a knot with a tie). Start the appliance, feed the mincer with mince and guide
the sausage skin as it fills up.
Note: this job is easier with two people, one to feed the appliance with mince, and the other to control the filling
of the sausage skin.
Make the sausages the required length by pinching and turning the sausage skin.
To make a good quality sausage, take care to avoid trapping air when filling and make the sausages 10 to 15 cm long
(separate the sausages by using a tie to make a knot).
VEGETABLE CUTTER (H)
Fitting (diagram 5 and 6):
Facing the motor unit, which should be unplugged, insert the storage unit H1 inclined to the right, aligning the ears
on the storage unit with the openings on the motor unit
E
. Insert the stem protruding from the storage unit
H1
into
the shaft of the motor unit
E
. Turn the feed tube of the storage unit H1 to the left until it reaches the stop.
Use:
• Select the cone corresponding to the required use.
• Place the selected cone in the opening at the front of the storage unit
H1
. The cone must be inserted fully into the
guide
(fig.7)
.
• Connect the appliance.
• Press once or twice on the start/stop button
(D)
to lock the cone
(fig. 8)
.
• Insert the foodstuffs into the feed tube of the storage unit
H1 (fig.9)
and push the foodstuff with the help of the
pusher
H2 (fig.10)
.
• To change cone, turn the storage unit
H1
by a quarter turn to the right, then turn it back to the vertical position
(fig. 11 and 12)
. Then remove the cone
(fig. 13)
.
Fitting the dicer attachment:
• Place the chip slicer cone in the opening at the front of the storage unit H1. The cone must be inserted fully into the
guide
(fig.16)
.
• Next fit the dicer attachment with the safety hinge open, centring the safety hinge in relation to the storage unit
feed tube
(fig.16)
.
• Check that the dicer attachment ring is correctly clipped to the base of the storage unit
(fig.17)
.
• Close the safety hinge onto the storage unit
(fig.17)
.
• Use the dicer function by inserting ingredients via the feed tube of the storage unit.
• Remove the dicer attachment by pulling the tab on the top of the safety hinge.
Tip: to make it easier to unlock the safety hinge H3f, simultaneously lift upwards and pull the tab to the front
with one finger (fig.18).
ATTENTION: Before using the appliance, ensure that the cone is correctly positioned on the guide.
3
Notice_2643049A:Mise en page 1 29/10/10 16:23 Page3