Device Configuration 5 - 33
Select either the
Inside
,
Outside
or
None
radio buttons.
•
Inside
- The inside network is transmitting data over the network to its intended destination. On the way out, the source
IP address is changed in the header and replaced by the (public) IP address.
•
Outside
- Packets passing through the NAT on the way back to the LAN are searched against the records kept by the NAT
engine. There the destination IP address is changed back to the specific internal private class IP address in order to reach
the LAN over the network.
•
None
- No NAT activity takes place. This is the default setting.
10. Set the following
DHCPv6 Client Configuration
. The
Dynamic Host Configuration Protocol for IPv6
(DHCPv6) provides a
framework for passing configuration information.
11. Set the following
MTU
settings for the virtual interface:
12. Within the
ICMP
field,
define whether ICMPv6 redirect messages are sent. Redirect requests data packets be sent on an
alternative route. This setting is enabled by default.
13. Within the
Address Autoconfiguration
field,
define whether to configure IPv6 addresses on this virtual interface based
on the prefixes received in router advertisement messages. Router advertisements contain prefixes used for link
determination, address configuration and maximum hop limits. This setting is enabled by default.
Stateless DHCPv6
Client
Select this option to request information from the DHCPv6 server using stateless DHCPv6.
DHCPv6 is a networking protocol for configuring IPv6 hosts with IP addresses, IP prefixes or
other configuration attributes required on an IPv6 network. This setting is disabled by default.
Prefix Delegation
Client
Specify a 32 character maximum request prefix for prefix delegation from a DHCPv6 server
over this virtual interface. Devices use prefixes to distinguish destinations that reside on-link
from those reachable using a router.
Request DHCPv6
Options
Select this option to request DHCPv6 options on this virtual interface. DHCPv6 options provide
configuration information for a node that must be booted using the network rather than
locally. This setting is disabled by default.
Maximum
Transmission Unit
(MTU)
Set the PPPoE client
maximum transmission unit
(MTU) from 500 - 1,492. The MTU is the
largest physical packet size in bytes a network can transmit. Any messages larger than the
MTU are divided into smaller packets before being sent. A PPPoE client should be able to
maintain its point-to-point connection for this defined MTU size. The default MTU is 1,492.
IPv6 MTU
Set an IPv6 MTU for this virtual interface from 1,280 - 1,500. A larger MTU provides greater
efficiency because each packet carries more user data while protocol overheads, such as
headers or underlying per-packet delays, remain fixed; the resulting higher efficiency means
a slight improvement in bulk protocol throughput. A larger MTU results in the processing of
fewer packets for the same amount of data. The default is 1,500.
Summary of Contents for WiNG 5.6
