manualshive.com logo in svg

Motorola MVME1X7P, Programmer'S Reference Manual, Page: 92 / 316

Share
Download
Motorola MVME1X7P Programmer'S Reference Manual Download Page 92

2-2

Computer Group Literature Center Web Site

VMEchip2

2

VMEbus-to-Local-
Bus Interface

Programmable VMEbus map decoder

Programmable AM decoder

Programmable local bus snoop enable

Simple VMEbus-to-local-bus address translation

8-bit, 16-bit and 32-bit VMEbus data width

8-bit, 16-bit and 32-bit block transfer

Standard and extended VMEbus addressing

Software-enabled write posting mode

Write post buffer (17 four-bytes in BLT mode, two four-bytes in non-
BLT mode)

An eight four-byte read ahead buffer (BLT mode only)

32-bit Local-Bus-to-
VMEbus DMA 
Controller

Programmable 16-bit, 32-bit, and 64-bit VMEbus data width

Programmable short, standard, and extended VMEbus addressing

Programmable AM code

Programmable local bus snoop enable

16 four-byte FIFO data buffer

Up to 4 GB of data per DMA request

Automatically adjustment of transfer size to optimize bus utilization

DMA complete interrupt

DMAC command chaining supported by a singly-linked list of DMA 
commands

VMEbus DMA controller requester with: 
– Software-enabled fair request modes;
– Software-configured release modes: 

Release-On-Request (ROR), and
Release-On-End-Of-Data (ROEOD); 

– Software-configured BR0-BR3 request levels; and
– Software enabled bus-tenure timer

VMEbus Interrupter

Software-configured IRQ1-IRQ7 interrupt request level

8-bit software-programmed status/ID register

Table 2-1.  Features of the VMEchip2 ASIC (Continued)

Function

Features

Summary of Contents for MVME1X7P





























































































































































































































































































































Reviews:

No comments