manualshive.com logo in svg

Motorola MVME1X7P, Programmer'S Reference Manual, Page: 85 / 316

Share
Download
Motorola MVME1X7P Programmer'S Reference Manual Download Page 85

Error Conditions

http://www.motorola.com/computer/literature

1-59

1

DMAC TEA - Cause Unidentified

SCC Retry Error

Description:

An error occurred while the DMAC was Local Bus master 
and additional status was not provided.

MPU Notification:

DMAC interrupt (when enabled)

Status:

The DLBE bit is set in the DMAC Status register (address 
$FFF40048 bit 6).

Comments:

An 8- or 16-bit write to the LCSR in the VMEchip2 causes 
this error. If the TBL bit is set (address $FFF40048 bit 2), 
the error occurred during a command table access; 
otherwise the error occurred during a data access. 

Description:

Local Bus Retry occurred due to VMEbus Dual Port Lock 
or LAN-wanted-Bus while the SCC was Local Bus master.

MPU Notification:

SCC Transmit Interrupt or SCC Receive Interrupt

Status:

SCC Transmit Interrupt Status register
SCC Transmit Current Buffer Address register
SCC Receive Interrupt Status register High
SCC Receive Current Buffer Address register PCCchip2 
SCC Error Status register ($FFF4201C)

Comments:

The DMA controllers in the SCC should not be 
programmed to access the VMEbus. Refer to the Serial 
Port Interface section in this chapter. SCC Transmit and 
Receive interrupt enables are controlled in the SCC and in 
the PCCchip2. 

Summary of Contents for MVME1X7P





























































































































































































































































































































Reviews:

No comments