Motorola DSP56K Manual Download Page 33 | Manualshive

Page: 33 / 637

background image

DATA ARITHMETIC LOGIC UNIT

MOTOROLA

DATA ARITHMETIC LOGIC UNIT

3 - 3

3.1

DATA ARITHMETIC LOGIC UNIT

This section describes the operation of the Data ALU registers and hardware. It dis-
cusses data representation, rounding, and saturation arithmetic used within the Data
ALU, and concludes with a discussion of the programming model.

3.2

OVERVIEW AND DATA ALU ARCHITECTURE

As described in Section 2, The DSP56K family central processing module is composed
of three execution units that operate in parallel. They are the Data ALU, address genera-
tion unit (AGU), and the program control unit (PCU) (see Figure 3-1). These three units
are register oriented rather than bus oriented and interface over the system buses with
memory and memory-mapped I/O devices.

The Data ALU (see Figure 3-2) is the first of these execution units to be presented. It bal-
ances speed with the capability to process signals that have a wide dynamic range and
performs all arithmetic and logical operations on data operands.

The Data ALU registers may be read or written over the XDB and the YDB as 24- or 48-
bit operands. The source operands for the Data ALU, which may be 24, 48, or 56 bits,
always originate from Data ALU registers. The results of all Data ALU operations are
stored in an accumulator.

The 24-bit data words provide 144 dB of dynamic range. This range is sufficient for most
real-world applications since the majority of data converters are 16 bits or less – and cer-
tainly not greater than 24 bits. The 56-bit accumulator inside the Data ALU provides 336
dB of internal dynamic range so that no loss of precision will occur due to intermediate
processing. Special circuitry handles data overflows and roundoff errors.

The Data ALU can perform any of the following operations in a single instruction cycle:
multiplication, multiply-accumulate with positive or negative accumulation, convergent
rounding, multiply-accumulate with positive or negative accumulation and convergent
rounding, addition, subtraction, a divide iteration, a normalization iteration, shifting, and
logical operations.

The components of the Data ALU are:

•

Four 24-bit input registers

•

A parallel, single-cycle, nonpipelined multiply-accumulator/logic unit (MAC)

•

Two 48-bit accumulator registers

•

Two 8-bit accumulator extension registers

•

An accumulator shifter

•

Two data bus shifter/limiter circuits

«
...
31
32
33
34
35
...
»

Summary of Contents for DSP56K






























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56K

Brand: TC-Helicon Pages: 18

PowerTrench MOSFET FDD6690A

Brand: Fairchild Pages: 6

Brand: Ampro Pages: 28

Brand: Coline Pages: 12

Brand: Nutri Ninja Pages: 21

Brand: Vitek Pages: 32

Brand: lab12 Pages: 7

Brand: Massive Audio Pages: 4

Design Mini Chopper 40959

Brand: Gastroback Pages: 28

Brand: Sound Storm Pages: 2

Brand: ABB Pages: 134

Brand: Termozeta Pages: 17

Brand: miniDSP Pages: 19

Brand: miniDSP Pages: 19

Brand: miniDSP Pages: 36

Brand: miniDSP Pages: 46

Brand: miniDSP Pages: 40

Brand: miniDSP Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands