MOTO GUZZI NORGE GT 8V Service Station Manual Download

Page: 259 / 357

NOTE

FOR EASY DRAINAGE OF THE OIL INSIDE THE PUMPING
MEMBER ROD, PRESS THE STEM IN THE WHEEL HOLD-
ER SLEEVE TO PUMP OIL OUT.

• Carefully check each part of the stem and make sure that there are no damaged elements.

• If there are no damaged or worn elements, refill the stem; otherwise, replace the damaged elements.

Disassembling the fork

•

Drain out all the oil in the stem.

•

Block the wheel holder sleeve with a

vice.

•

Unscrew the bottom screw and remove

it together with its gasket.

•

Remove the dust scraper using a

screwdriver as a lever.

CAUTION

BE CAREFUL NOT TO DAMAGE THE SLEEVE RIM AND
THE DUST SCRAPER.

Norge GT 8v

Suspensions

SUSP - 259

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands

MOTO GUZZI NORGE GT 8V, Service Station Manual

Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands