MOTO GUZZI NORGE GT 8V Service Station Manual Download

Page: 120 / 357

•

If shorted to positive: excessive voltage has been detected at PIN 10 of the BROWN con-

nector.

•

If the circuit is open, shorted to negative: voltage equal to zero has been detected at PIN 10

of the BROWN connector

Troubleshooting

•

shorted to positive: disconnect the coil connector, set the key to ON, activate the coil with

Navigator and check voltage at connector PIN 2: if there is voltage, restore the cable har-

ness; if voltage = 0, replace the coil

•

if the circuit is open, shorted to negative: check the coil connector and the Marelli control

unit connector. If they are not OK, restore; if everything is OK, check cable continuity be-

tween PIN 2 of the coil connector and PIN 10 of the BROWN connector. If there is not

continuity, restore the cable harness; if there is cable continuity, with the key set to KEY ON,

check the cable ground insulation (from coil connector or control unit connector). If this is

not OK, restore the cable harness.

Engine oil pressure sensor

Function:

Indicates the instrument panel if there is

enough oil pressure (0.35 +/- 0.15 bar) (5.1 +/-

2.18 PSI) in the engine.

Operation / Operating principle:

normally closed

switch. With oil pressure above 0.35 +/-0.15 bar

(5.1 +/- 2.18 PSI), open circuit.

Level in wiring diagram:

fuel reserve and oil pres-

sure.

Location:

•

Sensor: in between the engine "V", a

little to the left, under the generator

•

Connector: on the sensor.

Pin-out

: Voltage 12V

Instrument panel

Oil sensor failure DSB 07

Error cause

•

An oil sensor fault is signalled when, with engine off, it is detected that the sensor circuit is

open. The test is performed only once when the key is set to ON. There is an error when

the general warning light turns on.

Troubleshooting

Electrical system

Norge GT 8v

ELE SYS - 120

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands

MOTO GUZZI NORGE GT 8V, Service Station Manual

Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands