MOTO GUZZI NORGE GT 8V Service Station Manual Download

Page: 219 / 357

The connecting rods have a marked area for

weight selection.

The weight indicated in the chart includes screws,

dowels and the bushing.

CONNECTING ROD WEIGHT SELECTION

Specification

Desc./Quantity

Connecting rod - brown

0.588 - 0.598 mm (0.02074 - 0.02109 in)

Connecting rod - green

0.598 - 0.608 mm (0.02109 - 0.02145 in)

Connecting rod - black

0.608 - 0.618 mm (0.02145 - 0.02180 in)

Assembling the connecting rod

•

Lubricate the crankpin on which the

connecting rods are to be fixed.

•

If the connecting rods are not replaced,

be careful not to interchange the right

connecting rod with the left one and

vice versa.

To place the connecting rods: the two pins must

be facing the crankcase internal side.

•

Place the connecting rods and the

caps (B) on the crankshaft and fasten

them with new screws (A).

•

Remember these recommendations:

•

The screws fixing the connecting rods to the crankshaft must be replaced with new ones at

the following refitting as they are subject to high loads and stress;

•

The fitting clearance between bearing and connecting rod pin is 0.028 mm (0.0011 inch)

minimum and 0.052 mm (0.0020 inch) maximum;

•

The clearance between the shim washers of the connecting rod and those of the crankshaft

is comprised between 0.30 mm (0.01181 in) and 0.50 mm (0.01968 in);

•

Lock the screws (A) on the caps (B) with a torque wrench at the prescribed torque.

Norge GT 8v

Engine

ENG - 219

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands

MOTO GUZZI NORGE GT 8V, Service Station Manual

Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands