manualshive.com logo in svg

MOTO GUZZI NORGE GT 8V, Service Station Manual

The MOTO GUZZI NORGE GT 8V is a powerful and elegant touring motorcycle built for adventure. To ensure its optimal performance and maintenance, it is crucial to have the Service Station Manual. Easily download this comprehensive manual for free from manualshive.com to enhance your riding experience and keep your motorcycle in top shape.

Share
Download
background image

difference between the two pressures

is 1 cm Hg (1.33 kPa) maximum.

If this condition is detected:

•

take the engine back to idle and check

the depression values so that they are

aligned between the two cylinders.

Otherwise, open only the screw with

higher depression, using the by-pass

screws, to compensate.

If there is a larger difference:

•

act on the set screw of the throttle body

connecting rod to reduce the pressure

difference in the two pipes.

•

Repeat the procedure "Throttle posi-

tion self-acquisition" as explained

above.

•

Take the engine back to idle and check

the depression values so that they are

aligned between the two cylinders.

•

Otherwise, open only the screw with

higher depression, using the by-pass

screws, to compensate.

Recovery function

If the signal of the following sensors is interrupted, the control unit determines some values to keep the

engine running or it uses a different parameter. The instrument panel and the Navigator also signal the

problem.

RECOVERY

 

FUNCTION

Specification

Desc./Quantity

air temperature

25 °C (77 °F)

engine temperature

30 °C (86 °F)

with linear increase from the air temperature at ignition

barometric pressure

1010 hPa

throttle valve potentiometer

2.9° at idle, otherwise variable.

idle motor

fixed value variable depending on the vehicle

Using Navigator for injection system

Norge GT 8v

Power supply

P SUPP - 243

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten 

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Reviews:

No comments

Related manuals for NORGE GT 8V

Razor Indian eFTR Mini 2021 Owner'S Manual preview
Indian eFTR Mini 2021
Brand: Razor Pages: 20
Qlink LG250 User Manual preview
LG250
Brand: Qlink Pages: 44
hepco & becker Easyrack 6622520 01 01 Mounting Instructions preview
Easyrack 6622520 01 01
Brand: hepco & becker Pages: 4
hepco & becker 6609516 01 01 Quick Start Manual preview
6609516 01 01
Brand: hepco & becker Pages: 4
R&G LP0274BK Fitting Instructions Manual preview
LP0274BK
Brand: R&G Pages: 24
Honda st1300/a 2007 Setup Instructions preview
st1300/a 2007
Brand: Honda Pages: 28
ESAB WARRIOR TECH User Instructions preview
WARRIOR TECH
Brand: ESAB Pages: 4
Yamaha XSR700M 2021 Owner'S Manual preview
XSR700M 2021
Brand: Yamaha Pages: 104
Yamaha Super Tenere ABS 2018 Owner'S Manual preview
Super Tenere ABS 2018
Brand: Yamaha Pages: 122
Yamaha XSR900P Owner'S Manual preview
XSR900P
Brand: Yamaha Pages: 124
Yamaha XTZ 125K Owner'S Manual preview
XTZ 125K
Brand: Yamaha Pages: 97
DYNATEK D2K-HD1E User Instructions preview
D2K-HD1E
Brand: DYNATEK Pages: 10
Triumph 1050 Sprint Owner'S Handbook Manual preview
1050 Sprint
Brand: Triumph Pages: 126
Scott 2 Operation And Maintenance Instructions preview
2
Brand: Scott Pages: 22
SCORPION RKT-89 Fitting Instructions preview
RKT-89
Brand: SCORPION Pages: 2
SCORPION SIGS39 Installation Manual preview
SIGS39
Brand: SCORPION Pages: 15
F4Customs Can-Am Spyder RT Quick Start Manual preview
Can-Am Spyder RT
Brand: F4Customs Pages: 3
Wunderlich 44900-002/102 Fitting Instruction preview
44900-002/102
Brand: Wunderlich Pages: 5

Brands by name

Popular brands

Load more brands