manualshive.com logo in svg

MOTO GUZZI NORGE GT 8V, Service Station Manual

The MOTO GUZZI NORGE GT 8V is a powerful and elegant touring motorcycle built for adventure. To ensure its optimal performance and maintenance, it is crucial to have the Service Station Manual. Easily download this comprehensive manual for free from manualshive.com to enhance your riding experience and keep your motorcycle in top shape.

Share
Download
background image

Dashboard

Diagnosis

Changing the CODE

If you know the code, just enter it and then a new code that will be automatically stored in the memory.

If the vehicle is new, the user code is: 00000

Resetting the CODE

This function is used to set a new code when the old one is not available; in this case, at least two of

the programmed keys have to be inserted in the ignition lock.

After the first key has been inserted, the second one is requested with the following message:

INSERT KEY II

If the second key is not inserted within 20 seconds, the operation is finished.

After recognising the second key, the new code is required with the message:

ENTER NEW CODE

Once the operation is finished, the instrument panel goes back to the SET-UP menu.

DIAGNOSIS

Access to this menu (diagnosis functions), for the technical service only, after requesting a service code.

It will read: ENTER THE SERVICE CODE This vehicle code is: 

10695

The functions in this menu are:

•

Exit

•

ECU diagnosis

•

Instrument Panel Errors

•

Error Clearing

•

Reset Service

•

Update

•

Change Keys

•

km / Miles

ECU ERRORS

The instrument panel receives only the current errors from the control unit.

Description Error code

Throttle Valve Error DC V DC ECU 10

Throttle Valve Error DC Gnd ECU 11

Engine Temperature Error DC V DC ECU 14

Engine Temperature Error DC Gnd ECU 15

Air Temperature Error DC V DC ECU 16

Air Temperature Error DC Gnd ECU 17

Norge GT 8v

Electrical system

ELE SYS - 97

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten 

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Reviews:

No comments

Related manuals for NORGE GT 8V

Free Spirits 088305 Instructions Manual preview
088305
Brand: Free Spirits Pages: 32
Öhlins SD 053 Mounting Instructions preview
SD 053
Brand: Öhlins Pages: 8
HYOSUNG 2002 Comet 125 Service Manual preview
2002 Comet 125
Brand: HYOSUNG Pages: 199
HRC '92-RS125R Owner'S Manual preview
'92-RS125R
Brand: HRC Pages: 88
hepco & becker 5032536 00 01 Quick Start Manual preview
5032536 00 01
Brand: hepco & becker Pages: 3
BMW Motorrad F 900 XR Rider'S Manual preview
F 900 XR
Brand: BMW Motorrad Pages: 261
Corbin CA-BAG-ST Manual preview
CA-BAG-ST
Brand: Corbin Pages: 4
KTM 690 LC4 Owner'S Manual preview
690 LC4
Brand: KTM Pages: 90
AFX FX-55 International Owner’S Manual preview
FX-55
Brand: AFX Pages: 112
PUIG 0295 Mounting Instructions preview
0295
Brand: PUIG Pages: 2
Yamaha XV17ATMV(C) Road Star Owner'S Manual preview
XV17ATMV(C) Road Star
Brand: Yamaha Pages: 108
Yamaha XT250P Owner'S Manual preview
XT250P
Brand: Yamaha Pages: 100
Yamaha XTZ12D(C) Owner'S Manual preview
XTZ12D(C)
Brand: Yamaha Pages: 118
Yamaha Super Tenere ES 2022 Owner'S Manual preview
Super Tenere ES 2022
Brand: Yamaha Pages: 132
Yamaha XT250X 2008 Service Manual preview
XT250X 2008
Brand: Yamaha Pages: 282
Yamaha Super Tenere ES 2020 Owner'S Manual preview
Super Tenere ES 2020
Brand: Yamaha Pages: 130
Yamaha TDM850 User Manual preview
TDM850
Brand: Yamaha Pages: 211
Hudora 84201-03 Instructions On Assembly And Use preview
84201-03
Brand: Hudora Pages: 8

Brands by name

Popular brands

Load more brands