MOTO GUZZI NORGE GT 8V Service Station Manual Download Page 315 | Manualshive

Page: 315 / 357

background image

•

Once riding, the ABS system will be re-

activated only after riding faster than 5

km/h (3.1 mi/h) and the ABS warning

light (5) on the instrument panel (4)

turns off.

CAUTION

IF THE ABS SWITCH IS PRESSED FOR MORE THAN TEN
SECONDS, THE SYSTEM DETECTS A FAILURE. TO ACTI-
VATE THE ABS SYSTEM AGAIN TURN THE IGNITION
SWITCH TO "OFF" AND THEN TO "ON".

IN CASE OF FAILURE OR WITH ABS DISCONNECTED,
THE VEHICLE OPERATES AS IF IT DID NOT HAVE THIS
SYSTEM.

20 A fuse (ABS Main fuse) (6)

Protects: ABS Control unit.

Guide to diagnosis

PREMISE

Each time the key is ON, if, at least one current or

stored* error is detected, the ABS warning light

turns on permanently.

The ABS system is deactivated!

The system operates perfectly just as any other

braking system without ABS

* The diagnosis requires exceeding the 5 km/h

(3.1 mph).

Each time the key is ON, if at least one current or stored* error of the ABS system is not detected:

•

the ABS warning light flashes.

When the 5 km/h (3.1 mph) are exceeded:

- if errors are not detected: the ABS warning light turns off

- if at least one malfunction is detected: the ABS warning light turns on permanently.

The ABS system is deactivated!

Norge GT 8v

Braking system

BRAK SYS - 315

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

«
...
313
314
315
316
317
...
»

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Reviews:

No comments

Related manuals for NORGE GT 8V

Brand: Maico Pages: 13

Brand: Cannondale Pages: 102

Brand: KAYO MOTOR Pages: 74

Brand: KAYO MOTO Pages: 5

Brand: Yamaha Pages: 124

Apache RTR 160 HYPER EDGE 2015

Brand: TVS Pages: 60

Brand: R&G Pages: 15

Brand: Honda Pages: 150

Brand: Honda Pages: 137

Brand: GAS GAS Pages: 144

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 4

Brand: GPX Pages: 44

Brand: Arai Pages: 2

Brand: hepco & becker Pages: 3

Brand: Kemppi Pages: 10

Brand: LSL Pages: 4

Brand: Sealey Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands