MOTO GUZZI NORGE GT 8V Service Station Manual Download

Page: 113 / 357

Lambda sensor

Function

In charge of telling the control unit whether the

mixture is lean or rich.

Operation / Operating principle

The Marelli injection control unit reads and inter-

prets a voltage generated by the difference in oxy-

gen content between the exhaust fumes and the

ambient. It does not require an external supply

source but, in order to work properly, it should

reach a high operating temperature: that is why

there is a heating circuit inside.

Level in electrical circuit diagram:

Lambda sen-

sor

Location:

•

Sensor: on the exhaust conducts

•

Connector: near the probe

Electrical characteristics:

Heater circuit: 12 -14

at 20 °C (68 °F)

Pin-out:

1. Sensor (black wire)

2. Sensor signal - (grey wire)

3. Heater ground connection (white)

4. Heater power supply (white)

NAVIGATOR: PARAMETERS

Lambda sensor

example value: 0 - 1000 mV

If there is a short circuit at + 5 V or above, the value read is approx. 5.000 mV. If there is a short circuit

to ground instead, the value read is equal to 0 mV and the Lambda Sensor Correction parameter shows

25%: no error is displayed, though.

Lambda sensor correction

example value: 1.00

In closed loop, the value must be close to 0 % (values not within the +10 % and -10 % range may

indicate a fault):. In an open circuit, the lambda sensor signal is too low. Therefore, the control unit takes

it as a lean mixture condition and will try to enrich it. The value read will be +25%.

NAVIGATOR: ELECTRICAL ERRORS

Left lambda sensor P0130

- Shorted to positive.

Norge GT 8v

Electrical system

ELE SYS - 113

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands

MOTO GUZZI NORGE GT 8V, Service Station Manual

Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands