manualshive.com logo in svg

MOTO GUZZI NORGE GT 8V, Service Station Manual

The MOTO GUZZI NORGE GT 8V is a powerful and elegant touring motorcycle built for adventure. To ensure its optimal performance and maintenance, it is crucial to have the Service Station Manual. Easily download this comprehensive manual for free from manualshive.com to enhance your riding experience and keep your motorcycle in top shape.

Share
Download
background image

•

Remove the Moto Guzzi logo using a

screwdriver.

•

Remove the spark plug protection.

If the timing system is very noisy, check the clearance between the valves and the rocking levers.

NOTE

ADJUST WITH COLD ENGINE, WITH PISTON AT TOP DEAD CENTRE (TDC) IN COMPRESSION
STROKE (VALVES CLOSED).

•

Disconnect both spark plug boots.

•

Unscrew and remove the four head

cover fixing screws and collect the

sealing O-rings.

•

Remove the head cover together with

the gasket.

•

Loosen the nut (1).

•

Use a screwdriver to act on set screw

(2) until the following clearances are

obtained:

Technical specifications

Values valid with control clearance between

rockers and valve

Inlet valve: 0.15 mm (0.0059 in)

Exhaust valve: 0.20 mm (0.0079 in)

Maintenance

Norge GT 8v

MAIN - 66

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten 

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Reviews:

No comments

Related manuals for NORGE GT 8V

Kabuto HIKE Instruction Manual preview
HIKE
Brand: Kabuto Pages: 40
kellermann Atto Integral Installation Manual preview
Atto Integral
Brand: kellermann Pages: 2
Dynojet Power Commander III 718-411 Installation Instructions preview
Power Commander III 718-411
Brand: Dynojet Pages: 3
SW-Motech SBL.04.650.10000/B Quick Start Manual preview
SBL.04.650.10000/B
Brand: SW-Motech Pages: 2
National Cycle ZTechnik VStream Z2392 Installation Instructions preview
ZTechnik VStream Z2392
Brand: National Cycle Pages: 2
BMW R 1200 R Classic Technical Data preview
R 1200 R Classic
Brand: BMW Pages: 1
hepco & becker 5054558 00 01 Manual preview
5054558 00 01
Brand: hepco & becker Pages: 4
hepco & becker 6302523 00 01 Manual preview
6302523 00 01
Brand: hepco & becker Pages: 3
Shark SX 2 User Manual preview
SX 2
Brand: Shark Pages: 28
Malaguti X3Mnourd Workshop Manual preview
X3Mnourd
Brand: Malaguti Pages: 50
Malaguti MONTE 125 User Manual preview
MONTE 125
Brand: Malaguti Pages: 112
Beta RR 2T ENDURO 2013 250 Catalogue Of Spare Parts preview
RR 2T ENDURO 2013 250
Brand: Beta Pages: 58
KTM 60112092020 Information preview
60112092020
Brand: KTM Pages: 7
X-lite X-1004 Safety And Instructions For Use preview
X-1004
Brand: X-lite Pages: 52
Petzl Vertex HI-VIZ Manual preview
Vertex HI-VIZ
Brand: Petzl Pages: 20
Maico MOTOCROSS 250 1983 Owner'S Manual preview
MOTOCROSS 250 1983
Brand: Maico Pages: 83
GAS GAS FSR 450 - 2007 User Manual preview
FSR 450 - 2007
Brand: GAS GAS Pages: 68
Malossi 5517738 Manual preview
5517738
Brand: Malossi Pages: 24

Brands by name

Popular brands

Load more brands