MOTO GUZZI NORGE GT 8V Service Station Manual Download

Page: 126 / 357

check the correct sensor resistance: if it is not OK, replace the sensor; if it is OK, check

continuity of the brown cable between the sensor connector and PIN 18 of the instrument

panel connector: If not OK, restore the cable harness; if OK, with key set to ON, check if

there is voltage at the sensor connector PIN 1: if there is no voltage, replace the instrument

panel; if there is approximately 12V, restore the cable harness (there is a short circuit in the

battery). If there is 5V voltage, connect a 10 kOhm resistance to PIN 1 of the sensor con-

nector and to the vehicle ground connection: if, with key set to ON, the voltage measured

upstream the resistance decreases, replace the instrument panel. If voltage continues to be

approximately 5V, restore the pink cable (there is a short circuit at + 5V).

Notes

If a short circuit to ground is detected at PIN 9 of the instrument panel connector, the display will show

a full scale air temperature indication of 60 °C (140 °F).

Check the ground insulation of the sensor connector pink cable: if there is a connection, restore the

cable harness; if it is earth insulated, check that sensor resistance is correct: if it is not OK, replace the

sensor; if it is OK, replace the instrument panel.

RUN/STOP switch

Function

It tells the control unit if the driver wishes to enable

engine start-up or to keep the engine running.

Operation / Operating principle

If the driver wants to shut off the engine or to dis-

able engine start-up, the switch should be open,

i.e. the Marelli control unit should not detect volt-

age at PIN 27 of the BLUE connector.

Level in electrical circuit diagram:

start-up ena-

bling switches.

Location:

•

right light switch.

•

connector: right side, near the coil.

Electrical characteristics:

•

STOP position: the circuit is open

•

RUN position: closed circuit (continui-

ty)

PIN:

Electrical system

Norge GT 8v

ELE SYS - 126

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for NORGE GT 8V






































































































































































































































































































































































Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands

MOTO GUZZI NORGE GT 8V, Service Station Manual

Search results

Summary of Contents for NORGE GT 8V

Reviews:

Related manuals for NORGE GT 8V

Brands by name

Popular brands