DYNASTY 2006
ELECTRICAL SYSTEMS - CHASSIS — SECTION 9 • 289
To use the Cummins High Idle Feature:
• With the cruise control
OFF
, Press and release the
RES
button. Each time the switch is pressed and
released, the idle will rise 25 RPMs, from 600-800 RPM. To lower the idle, press and release the
SET
button. Engine idle speed will decrease in 25 RPM increments.
• With the Cruise Control
ON
, press and release the
RES
button once. Engine speed will increase to 1200
RPM. Push and hold the
RES
button, engine speed will increase to 1500 RPM. Use
CANCEL
or turn the
cruise control
OFF
to return the engine to an idle.
• With the Cruise Control
ON
, press the
SET
button once. Engine will increase to 1000 RPM. Press and
hold the
SET
button, engine speed will decrease to 950 RPM. Use
CANCEL
or turn the cruise control
OFF
to return the engine to idle.
NOTE:
The transmission will not shift into gear if the engine RPM is at or above 900. The display
will flash “6” indicating the engine RPM is excessive. Select “N” and lower the engine RPM.
The brake also deactivates high idle.
Wiper Function
The windshield wipers are driven by a single motor. Any wiper function generates
a Headlamp On signal from the Master Controller. To disengage automatic headlight
illumination, turn off the ignition, or activate and then deactivate the dashboard
headlamp switch.
Marker Flashlamp:
Pressing Marker Flash lamp causes the taillights and all marker lights to
momentarily fl ash.
OFF:
Cancels all wiper operations. Wiper function is also cancelled when the
ignition is turned off.
HI-LO:
When the button is pressed, wipers activate on low speed. If the button is pressed again, the
high wiper speed setting is activated. Subsequently pressing the
HI-LO
button will alternate
wiper operation between low and high speed mode.
Wiper Wash:
Activates the wash pump relay while the button is pressed. If no wiper function has been
selected, the low wiper will activate for a period of approximately three wiper cycles, after the
switch is released. If any wiper functions have been selected, the wipers will continue to run in
the selected mode after the Wiper Wash button is released.
Wiper Variable:
Operation of the Wiper Variable button causes the low speed wiper function to activate for
one wipe. If the button is pressed again within approximately 30 seconds, the low speed wiper
function activates again and repeats at an interval determined by the time between the last two
operations of the button. Additional button operations will shorten the cycle. Activating other
wiper modes cancels the variable mode.
090270
Summary of Contents for DYNASTY 2006
