Mobatime DTS 4801.masterclock Instruction Manual Download

Page: 44 / 120

44 / 120

800652.11

Channel state:

Display of all 64 channels of the switch functions. A switched on channel is displayed
with an [*].

[ ]

shows a locked channel in a switched off state whereas

[*]

shows a

switched on channel in a locked state.
An

shows that the channel is linked to a control output.

shows that the channel is linked to the twilight calculation.

By entering a channel, the page can be changed to that of manual switching for that
channel:

After a restart or after changing the program file, it can take up to 2 min until the states
displayed correspond to the effective states on the channel relay.

Summary of Contents for DTS 4801.masterclock

























































































































Search results

Summary of Contents for DTS 4801.masterclock

Reviews:

Related manuals for DTS 4801.masterclock

Brands by name

Popular brands

Mobatime DTS 4801.masterclock, Instruction Manual

Search results

Summary of Contents for DTS 4801.masterclock

Reviews:

Related manuals for DTS 4801.masterclock

Brands by name

Popular brands