Mobatime DTS 4801.masterclock Instruction Manual Download Page 48

Page: 48 / 120

48 / 120

800652.11

6.5.14 NTP

server

NTP can run as server or combined as server/client.
To run NTP as source (NTP as client), in the menu ’2 Configuration’



'2 Time

handling'



’3 NTP Server / NTP Sources’ at least one server has to be set.

The exact behavior of NTP time sources is described in chapter “8.2 Time take-over,
NTP“.

Further 2 multicast or broadcast addresses can be configured:

1.-4. Summary about configured NTP – time sources. Select to configure and display

changes to the menu "ENTRY TIMESOURCE"

5.-6. Summary about configured NTP – broadcast addresses. Select to

configure and display changes to the menu “NTP MULTI- / BROADCAST-
ENTRY“

7. NTP Authentication: Changes to the menu “NTP AUTHENTICATION“

Information about a multicast – address, configured for NTP slave clocks.

Summary of Contents for DTS 4801.masterclock

























































































































Search results

Summary of Contents for DTS 4801.masterclock

Reviews:

Brands by name

Popular brands

Mobatime DTS 4801.masterclock, Instruction Manual

Search results

Summary of Contents for DTS 4801.masterclock

Reviews:

Brands by name

Popular brands