Mobatime DTS 4801.masterclock Instruction Manual Download

Page: 26 / 120

26 / 120

800652.11

6.5 Configuration

menu

Configuration of the DTS 480x via different sub-menus:

1. Configuration of the lines / outputs (MOBALine, impulse line, DCF active code line,

DCF out, RS485 line, serial telegrams, NTP slave clock lines, switch functionality)
see chapter "6.5.1 Lines"

2. Configuration of the time source, time keeping, etc.

See chapter "6.5.11 Time handling"

3. Alarm settings (alarm relais, e-mail, SNMP)

See chapter "6.5.17 Alarms"

4. General settings for the DTS 480x (language, time zone for alarms and display,

password for menu...)
See chapter "4.4.21 General settings"

5. Netzwork settings

See chapter "6.5.23 Network"

6. Services (switch network services such as FTP, Telnet, SSH on or off)

See chapter "6.5.24 Services (Network services FTP, Telnet, SSH....)"

7. SNMP configuration for GET/PUT.

See chapter "6.5.25 SNMP" (Traps are dealt with in menu ’2. Configuration’



’3. Alarms’



’3. Traps’. See also chapter 6.5.21 SNMP Traps)

Summary of Contents for DTS 4801.masterclock

























































































































Search results

Summary of Contents for DTS 4801.masterclock

Reviews:

Related manuals for DTS 4801.masterclock

Brands by name

Popular brands

Mobatime DTS 4801.masterclock, Instruction Manual

Search results

Summary of Contents for DTS 4801.masterclock

Reviews:

Related manuals for DTS 4801.masterclock

Brands by name

Popular brands