Mobatime DSC. 250.4 Instruction Manual Download

Page: 93 / 144

DA series

BE-801372.01-Digital_clocks_manual-221114

©MOBATIME

7.5.7

Cable connection

A+

B-

GND

IN+

IN-

DC OUT +

DC OUT -

COM

–

brown

white

red

black

DC IN connection

red

blue

white

red

blue

white

brown

white

green

brown

white

brown

white

yellow

green

Installation LINES / DC OUT wire connection

TEMP wire connection – 1 or 2 temperature sensors

RS 485 wire connection

CTRL wire connection

(stopwatch control connects to TEMP connector)

RELAY wire connection

7.6

7.6.1

Description

Basic features

•

digits of 18, 45 or 57 mm height, which corresponds to readability distance of 8, 20 or 25 m.

• digits in red, pure green blue, yellow, and white color
•

display composed of SMD LEDs

•

manual or automatic adjustment of the luminosity of LED diodes

•

altering time, date and temperature display with adjustable time period

•

time display format in four digits (HH : MM) or six digits (HH : MM

or HH : MM : SS), 12 or 24‑hour

cycle

•

date display format in four digits (DD. MM.) or six digits (DD. MM.

or DD. MM. YY)

•

AM/PM indication for 12‑hour cycle

•

temperature display in °C or °F (providing the temperature sensor is connected)

•

TEMP connector is used to connect temperature sensors or stopwatch control

Mechanic

•

clock frame made of anodized aluminium profiles, black or silver color

•

anti‑reflection front cover made of plexiglass

• single or double sided design
•

wall mounting (for single sided design), ceiling suspension, wall bracket, flush mounting or table

standing

•

push buttons placed on the upper side of the clock frame

•

protection degree IP 40 (IP 20 for DA.18 table mounting)

• working temperature 0 to +50 °C

Synchronization

•

autonomous operation with internal quartz time base

•

accuracy ±0.1 s/day without synchronization (after 24 hours of synchronization at constant

temperature)

•

NTP multicast or unicast synchronization, Ethernet or WiFi network, PoE or mains powered

•

slave clock operation with synchronization by MOBATIME serial code, MOBALine, DCF, impulse line

or by IRIG‑B, mains powered

•

RTC backup with supercapacitor (lithium battery on request)

Configuration

•

setting of the clock parameters and time / date by means of push buttons or IR remote control

Networkconnectionoptions

•

IPv4 and IPv6 support

•

DHCPv4, DHCPv6 / manual configuration of the clock parameters or configuration via web interface

•

DHCPv4, DHCPv6 private strings allow easy configuration of the clock parameters when connected

to LAN

Summary of Contents for DSC. 250.4

















































































































































Search results

Summary of Contents for DSC. 250.4

Reviews:

Related manuals for DSC. 250.4

Brands by name

Popular brands

Mobatime DSC. 250.4, Instruction Manual

Search results

Summary of Contents for DSC. 250.4

Reviews:

Related manuals for DSC. 250.4

Brands by name

Popular brands