Mobatime DSC. 250.4 Instruction Manual Download

Page: 43 / 144

Firmware update

BE-801372.01-Digital_clocks_manual-221114

©MOBATIME

FIRMWARE UPDATE

Firmware update can be done in several ways, such as:

•

management software MOBA‑NMS

• WEB server
•

SNMP

6.1

Firmware update via MOBA‑NMS

For instruction about firmware update via MOBA‑NMS, please visit

http://www.mobatime.com

6.2

Firmware update via WEB server

•

Install TFTP server (e.g.

tftpd32

•

Allow UDP port 69 on your firewall.

•

Place firmware file with name

device.upd

to folder from which your TFTP server serve files.

•

Open web interface of digital clock, which you want to update.

PRINT-SEARCH

Type IP address of clock to the URL bar of your browser.

• In the web interface, please navigate to section

Command

•

Update will be invoked by pressing

Apply

•

In dependence of your TFTP server, information about update progress is displayed.

•

Wait about 1 minute after firmware download.

•

Check whether the firmware version is correct.

If the firmware version is not correct, it is necessary to repeat procedure.

6.3

Firmware update via SNMP

•

Install TFTP server (e.g.

tftpd32

•

Allow UDP port 69 on your firewall.

•

Place firmware file with name

device.upd

to folder from which your TFTP server serve files.

•

Open your SNMP manager software and load MIB file.

•

Find variable

mbnscCommandFirmwUpd

and set it to

device.upd

•

In dependence of your TFTP server, information about update progress is displayed.

•

Wait about 1 minute after firmware download.

•

Check whether the firmware version is correct.

If the firmware version is not correct, it is necessary to repeat procedure.

Summary of Contents for DSC. 250.4

















































































































































Search results

Summary of Contents for DSC. 250.4

Reviews:

Related manuals for DSC. 250.4

Brands by name

Popular brands

Mobatime DSC. 250.4, Instruction Manual

Search results

Summary of Contents for DSC. 250.4

Reviews:

Related manuals for DSC. 250.4

Brands by name

Popular brands