Mitsubishi MOTORS i-MiEV Owner'S Manual Download Page 133 | Manualshive

Page: 133 / 297

background image

Service brake

5-24

Features and controls

5



When the vehicle speed is approximately
2-22 mph (3-35 km/h).

The system will not operate under the follow-
ing conditions:



When the vehicle speed is approximately
2 mph (3 km/h) or less and the brake
pedal is depressed.



When the vehicle speed is approximately
22 mph (35 km/h) or more.



When the selector lever is in the “P”
(PARK) position.

Under normal conditions, the indicator light
in the instrument cluster illuminates when the
electric motor switch is turned to the “ON”
position and goes off a few seconds later.
Always confirm the indicator light goes off
before driving.

N00517500305

Overuse of the brake can cause poor brake
response and premature wear of the brake
pads.

N00517600423

Your vehicle is equipped with power brakes
for more braking force with reduced brake
pedal effort.
Your brakes are designed to operate at full
capacity, even if the power assist is lost.
If the power assist is lost, the effort needed to
press the brake pedal is greater.
If you should lose the power assist for some
reason, the brakes will still work.
If the power brake unit or either of the two
brake hydraulic systems stop working prop-

WARNING



Always pay special attention to pedestri-
ans. Even if the acoustic vehicle alerting
system (AVAS) sounds, pedestrians may
not notice your vehicle.

NOTE



If the indicator light blinks, turn the electric
motor switch back to the “LOCK” position
and again turn the switch to the “ON” posi-
tion.
It is not a malfunction if the indicator light
goes off. If the indicator light blinks again,
however, have the vehicle inspected at a cer-
tified i-MiEV dealer as soon as possible.

Service brake

Brake pedal

WARNING



Do not leave any objects near the brake
pedal or let a floor mat slide under it;
doing so could prevent the full pedal
stroke that would be necessary in an
emergency. Make sure that the pedal can
be operated freely at all times. Make sure
the floor mat is securely held in place.

CAUTION



It is important not to drive the vehicle with
your foot resting on the brake pedal when
braking is not required. This practice can
result in very high brake temperatures, pre-
mature pad wear, and possible damage to the
brakes.

Power brakes

BK0220400US.book 24 ページ２０１４年１１月１８日　火曜日　午前７時２７分

«
...
131
132
133
134
135
...
»

Summary of Contents for i-MiEV










































































































































































































































































































Reviews:

No comments

Related manuals for i-MiEV

Brand: PAC Pages: 15

Brand: RaceChip Pages: 20

Brand: RAM Commercial Pages: 12

Brand: Ford Pages: 2

Brand: iArmor Pages: 6

Brand: Camcar Pages: 2

Camaro 12000 1968 Series

Brand: Chevrolet Pages: 455

Brand: Wagan Pages: 8

Brand: Thermo King Pages: 2

Brand: IBASE Technology Pages: 100

S2000 Windscreen Camera Mount

Brand: Modifry Products Pages: 2

Brand: AutoWatch Pages: 4

Brand: Globalsat Pages: 2

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Brand: Quadratec Pages: 12

BEDXTENDER HD MAX 74841-00A

Brand: AMP Research Pages: 9

Brand: Belkin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands