manualshive.com logo in svg

Mitsubishi MOTORS i-MiEV, Owner'S Manual

The Mitsubishi MOTORS i-MiEV electric vehicle is a sustainable and innovative transportation solution. To ensure optimal usage, we provide a comprehensive user manual that can be downloaded for free from our website. Discover all the features and functionalities of the i-MiEV by accessing the manual directly at manualshive.com.

Share
Download
background image

High-Voltage components

3-34

General information/Charging

3

N01205700027

High voltage components and wiring cables
are located as shown in the figure below.

N01205800031

A crash or impact significant enough to
require an emergency response for conven-

tional vehicles would also require the same
response for electric vehicles.
Also follow the instructions described below
to avoid severe burns and electrical shock that
may result in serious injury or death.

EV (Electric Vehicle) 
system does not start 
after quick charging.

The vehicle has a malfunction.

Contact a certified i-MiEV dealer.
If you need to push the vehicle, turn the electric motor switch to the “ON” posi-
tion and move the selector lever to the “N”(NEUTRAL) position.

Symptom

Possible cause

Possible solution

High-Voltage components 

WARNING

The EV (Electric Vehicle) system uses high
voltage up to DC 330 volt. The system can
be hot during and after starting and when
the vehicle is shut off. Be careful of both
the high voltage and the high temperature.
Follow the warning labels that are
attached to the vehicle.

Never touch, disassemble, remove or
replace high-voltage parts, exposed elec-
trical components, cables or connectors.
Failure to follow this instruction can
result in severe burns or electric shock
causing serious injury or death. High-volt-
age cables are colored orange. The vehicle
high voltage system has no user service-
able parts. Take your vehicle to a Certified
i-MiEV dealer for any necessary mainte-
nance.

Always assume the high voltage battery
and associated components are energized
and fully charged.

1- Regular charge port
2- MCU
3- Main drive lithium-ion battery
4- Heater
5- Air conditioner compressor
6- High voltage connector
7- Service plug
8- Electric motor (Electric motor unit)
9- On board charger/DC-DC converter

10- Quick charge port

In case of a collision 

WARNING

If your vehicle is drivable, pull your vehi-
cle off the road to a safe, nearby location
and remain on the scene.
Also, if possible, do the following opera-
tions and stay out of the way of any
oncoming traffic while awaiting the
arrival of emergency responders.
• Apply chocks to the wheels.
• Move the selector lever to the “P”

(PARK) position.

• Apply the parking brake.
• Open the windows, doors and liftgate.
• Turn the electric motor switch to the

“LOCK” position.

• Turn on the hazard warning flashers.
• Move the key away from the vehicle to

prevent unintended start-up of the sys-
tem by inadvertent contact with a switch
or impact from the crash.

BK0220400US.book  34 ページ  ２０１４年１１月１８日　火曜日　午前７時２７分

Summary of Contents for i-MiEV










































































































































































































































































































Reviews:

No comments

Related manuals for i-MiEV

iDataLink maestro Rr Install Manual preview
maestro Rr
Brand: iDataLink Pages: 106
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Brand: Buick Pages: 428
EZTRUNK PHANTOM JK Assembly Manual preview
PHANTOM JK
Brand: EZTRUNK Pages: 3
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Brand: Safe Fleet Pages: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Brand: Honda Pages: 4
S3 Power Sports S3193 Installation Instructions preview
S3193
Brand: S3 Power Sports Pages: 2
Subaru 2004 Impreza OUTBACK SPORT Owner'S Manual preview
2004 Impreza OUTBACK SPORT
Brand: Subaru Pages: 34
Toyota Avalon 2001 Operating Manual preview
Avalon 2001
Brand: Toyota Pages: 295
EUFAB 11512 Manual preview
11512
Brand: EUFAB Pages: 4
TomTom LINK 105 Installation Manual preview
LINK 105
Brand: TomTom Pages: 22
Mitsubishi Montero 1988 Manual preview
Montero 1988
Brand: Mitsubishi Pages: 367
Honda CRV 2015 Navigation Manual preview
CRV 2015
Brand: Honda Pages: 253
Toyota 2018 yaris Vehicle Instruction Card preview
2018 yaris
Brand: Toyota Pages: 11
Belkin F8J034 User Manual preview
F8J034
Brand: Belkin Pages: 30
Mitsubishi FTO Series Handbook preview
FTO Series
Brand: Mitsubishi Pages: 141
Lincoln 2017 MKC Owner'S Manual preview
2017 MKC
Brand: Lincoln Pages: 538
LaserLine 921K Operating Instructions preview
921K
Brand: LaserLine Pages: 4
Gold Lantern GL-VTMK20 Specifications preview
GL-VTMK20
Brand: Gold Lantern Pages: 1

Brands by name

Popular brands

Load more brands