Mitsubishi MOTORS i-MiEV Owner'S Manual Download Page 69 | Manualshive

Page: 69 / 297

background image

MiEV Remote System

3-54

General information/Charging

3

Charging Timer is
not possible.

The system is charged
although the ON timer is
being set.

Backup charging for the Main Drive Lith-
ium-ion Battery Warming System has
been operated.

This is not a malfunction.Charging will be termi-
nated when the system has been charged enough for
the Main Drive Lithium-ion Battery Warming Sys-
tem.

Charging is preset, but
the specified charging
level is not satisfied.



The charging level is
not expected amount.



Is not charged.



Is not charged at the
preset time.

The timer is cancelled or the preset time is
changed by using another MiEV Remote.

Check whether another person has operated his or
her MiEV Remote.

The electric motor switch has been oper-
ated before the system is charged.

Check whether the electric motor switch has been
operated before the system is charged.

The temperature of the Main Drive Lith-
ium-ion Battery has exceeded about
140 °F (60 °C).

Allow the temperature of the Main Drive Lithium-
ion Battery to reach normal operating temperature.
Refer to “Cautions and action to deal with intense
heat” on page 3-8.

Charging Timer is not preset correctly.

Preset the timed charging again.

Although the charging is
preset, too much time is
needed to charge the sys-
tem fully.

The Remote Climate Control has been
activated.

Check whether the Remote Climate Control has
been activated.

The Main Drive Lithium-ion Battery
Warming System has been operated.

Move the vehicle to a warmer location.

Temperature of the Main Drive Lithium-
ion Battery is low.

Refer to “Cautions and action to deal with intense
cold” on page 3-10.

Charging Timer is
not possible.

It is not fully charged.

If the charging unit is equipped with the
timer function, the power supply to the
unit has been cut off.

Preset the Charging Timer while the charging unit
with timer function is powered on.

Phenomena

Cause

Remedy

BK0220400US.book 54 ページ２０１４年１１月１８日　火曜日　午前７時２７分

«
...
67
68
69
70
71
...
»

Summary of Contents for i-MiEV










































































































































































































































































































Reviews:

No comments

Related manuals for i-MiEV

Brand: Xblitz Pages: 16

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Chariot Carriers Pages: 3

Brand: V8 equipment Pages: 17

Brand: Subaru Pages: 21

Brand: STC Pages: 6

Brand: Nav TV Pages: 4

Brand: Havis Pages: 5

Brand: Fab Fours Pages: 21

2007 SLR Mclaren

Brand: Mercedes-Benz Pages: 425

Brand: Rydeen Pages: 14

Brand: EUFAB Pages: 20

Brand: Toyota Pages: 204

Turnoverball 1020

Brand: Bowers & Wilkins Pages: 6

Brand: Buzz Rack Pages: 8

Brand: Front Runner Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands