Mitsubishi MOTORS i-MiEV Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 297

background image

Charging troubleshooting guide

3-32

General information/Charging

3

Regular charging can-
not be started.

There is no electrical power coming
from the outlet.

Confirm that there has not been a power failure. Make sure the breaker is on. If
an outlet with a timer device installed is used, power will only be available at
the time set by the timer.
Confirm if the POWER indicator on the control box is illuminated.

The charge connector is not con-
nected correctly.

Confirm the charge connector is connected correctly.

The charge connector was connected
and disconnected repeatedly in a
short time.

Disconnect the charge connector, wait for a while, then start charging procedure
again from the beginning.

A charging cable for other vehicle is
used.

Use the EV charging cable only for your vehicle.

The regular charger may not be
compatible with your vehicle.

Ask an administrator or the manufacturer of the regular charger whether the
charger is compatible with your vehicle. Always follow the instructions shown
on the regular charger.

Charging Timer by
MiEV remote cannot
be started.

Refer to “Action to be taken when the MiEV Remote system does not operate correctly” on page 3-51.

Symptom

Possible cause

Possible solution

BK0220400US.book 32 ページ２０１４年１１月１８日　火曜日　午前７時２７分

«
...
45
46
47
48
49
...
»

Summary of Contents for i-MiEV










































































































































































































































































































Reviews:

No comments

Related manuals for i-MiEV

Brand: K&M Pages: 3

Brand: Carax Pages: 2

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

Brand: Kolpin Pages: 25

Brand: Code 3 Pages: 8

Brand: Toyota Pages: 371

Brand: Motoalliance Pages: 8

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: ULTIMATE SPEED Pages: 40

Brand: Rugged Ridge Pages: 2

Brand: Arrista Pages: 2

EPS-LD SafePark

Brand: Tobe Pages: 2

Brand: Lexus Pages: 878

Brand: EUFAB Pages: 18

Brand: Ford Pages: 264

Brand: Metra Electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands