Mitsubishi Electric PUHY-P250YJM-A Service Manual Download Page 191 | Manualshive

Page: 191 / 272

background image

[

X

Troubleshooting ]

- 182 -

HWE10190

GB

In case of ME remote controller

3. Phenomena

"PLEASE WAIT" display on the remote controller does not disappear, and no operation is performed even if the button is

pressed.

(1) Cause
Without using MELANS

1) Outdoor unit address is set to "00"
2) A wrong address is set.

The address of the indoor unit that is connected to the remote controller is incorrect. (It should equal the ME remote controller

address plus 100.)

A wrong address is set to the ME remote controller. (100 must be added to the address of the indoor unit.)

3)   Faulty wiring of the terminal block for transmission line (TB5) of the indoor unit in the same group with the remote controller.
4)   The centralized control switch (SW2-1) on the outdoor unit is set to ON.
5)   Disconnection or faulty wiring of indoor unit transmission line.
6)   Disconnection between the terminal block for M-NET line connection (TB5) of the indoor unit and the male connector (CN2M)
7)   The male power supply connectors on 2 or more outdoor units are connected to the female power supply switch connector

(CN40) for the transmission line for centralized control.

8) Outdoor unit control board failure
9) Outdoor unit control board failure
10) Remote controller failure

Interlocking control with MELANS

1)   No group registration is made using MELANS. (The indoor unit and the ME remote controller are not grouped.)
2)   Disconnected transmission line for centralized control (TB7) of the outdoor unit
3)   The male power supply connector is connected to CN40 on more than one outdoor unit, or the connector is connected to CN40

on the outdoor unit in the system to which a power supply unit for transmission line is connected.

Using MELANS

1) When MELANS is used, "PLEASE WAIT" display on the remote controller will disappear when the indoor unit and the local

remote controller (ME remote controller) are grouped.
If "PLEASE WAIT" does not disappear after the registration, check the causes (2) 1) - 3).

(2) Check method and remedy

YES

YES

YES

YES

YES

YES

YES

NO

NO

*1

*1. When the indoor unit address is set to 1 - 50, the address will be forcibly set to 100.

NO

NO

NO

NO

NO

Without using MELANS

Are all the units in the system
experiencing the same problem?

Check the address of
the outdoor unit.

51 - 100?

Check the centralized centralized
switch (SW2-1) on the outdoor unit.

ON?

Indoor unit control board failure

A wrong address is
set to the outdoor unit.

Wrong switch setting
Change it from
ON to OFF.

A wrong address is
set to the ME
remote controller.

A wrong address is
set to the indoor unit.

Wrong wiring of the
M-NET transmission
line of the indoor unit

Disconnected
connector (CN2M)

Correct
the error.

Disconnected?

17 - 30V?

ME remote controller

- 100?

Check the address of the
indoor unit to be coupled.

Indoor unit + 100?

Check the address of the ME remote controller
on which "PLEASE WAIT" is displayed.

Check connection between indoor M-NET
transmission terminal block (TB5) and the
male connector (CN2M)

Measure voltages of the terminal
block for M-NET transmission line
on the indoor unit.

Indoor unit board or
remote controller failure

0000002115.book 182 ページ２０１１年６月４日　土曜日　午前１０時４８分

«
...
189
190
191
192
193
...
»

Summary of Contents for PUHY-P250YJM-A

















































































































































































































































































Reviews:

No comments

Related manuals for PUHY-P250YJM-A

Brand: Daikin Pages: 12

Brand: Patton Pages: 4

Brand: Payne Pages: 32

Brand: Samsung Pages: 16

Brand: Turbo Air Pages: 19

SkyAir FBQ18PVJU

Brand: Daikin Pages: 18

Brand: EdgeStar Pages: 26

Brand: GE Pages: 28

Brand: Daikin Pages: 15

Brand: York Pages: 20

Brand: ulsonix Pages: 21

Brand: Bard Pages: 21

Brand: Delta Pages: 32

Brand: Pure n Natural Systems Pages: 4

Brand: EUROM Pages: 52

Brand: ICP Pages: 12

Brand: Solair Pages: 39

Brand: Omega Altise Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands