Mitsubishi Electric FR-A8ND Instruction Manual Download Page 36

Page: 36 / 104

INVERTER SETTING

4.5 Inverter reset



Operation conditions of inverter reset

Which resetting method is allowed or not allowed in each operation mode is described below.



Inverter reset can be made any time.



Reset can be made only when the protective function of the inverter is activated.

NOTE

• When a communication line error has occurred, reset cannot be made from the network.
• The inverter is set to the External operation mode if it has been reset in Network operation mode in the initial status.

To resume the network operation, the inverter must be switched to the Network operation mode again.
Set a value other than "0" in

Pr.340

to start in the Network operation mode. (Refer to

page 27

• The inverter can not be controlled for about 1 s after release of a reset command.

Resetting method

Operation mode

Network

operation

External

operation

PU operation

Reset from the
network

Inverter reset (Class 0x2A, Instance 1, Attribute 101) (Refer
to

page 77

)



Allowed

Disallowed

Error reset at inverter fault
(Refer to

page 45

)



Pr.349

= 0

Allowed

Pr.349

= 1

Disallowed

Turn on the inverter RES signal (terminal RES)

Allowed

Switch off inverter power

Allowed

Reset from the PU/
DU

Inverter reset

Allowed

Reset at inverter fault

Allowed

Summary of Contents for FR-A8ND









































































































Search results

Summary of Contents for FR-A8ND

Reviews:

Related manuals for FR-A8ND

Brands by name

Popular brands

Mitsubishi Electric FR-A8ND, Instruction Manual

Search results

Summary of Contents for FR-A8ND

Reviews:

Related manuals for FR-A8ND

Brands by name

Popular brands