Mindray BeneFusion SP3 Service Manual Download

Page: 6 / 80

4 Troubleshooting ...................................................................................................4-1

4.1 Overview ..............................................................................................................4-1

4.2 Part Replacement ................................................................................................4-1

4.3 Checking Syringe Pump Status ..........................................................................4-1

4.4 Fault List ..............................................................................................................4-2

4.4.1 SP3 System Fault and Exception Code ..................................................4-2

4.4.2 Other Faults .............................................................................................4-7

5 Repair and Disassembly ......................................................................................5-1

5.1 Tools Preparation.................................................................................................5-1

5.2 Disassembly steps ..............................................................................................5-1

5.2.1 Disassembling Front and Rear Covers (Note: You should wear an

anti-static wristband throughout) ......................................................................5-1

5.2.2 Removing the Push and Pull Box Assembly (Note: You should wear an

anti-static wristband throughout) ......................................................................5-3

5.2.3 Removing the Pump Body Assembly (Note: You should wear an

anti-static wristband throughout) ......................................................................5-5

5.2.4 Disassembling Front Cover Assembly (Note: You should wear an

anti-static wristband throughout) ......................................................................5-7

5.2.5 Disassemling the Pump Body Assembly (Note: You should wear an

anti-static wristband throughout) ................................................................... 5-10

5.2.6 Disassembling Rear Cover Assembly (Note: You should wear an

anti-static wristband throughout) ................................................................... 5-13

6 Components ..........................................................................................................6-1

6.1 Host .....................................................................................................................6-1

6.1.1 Exploded View .........................................................................................6-1

6.1.2 Host Parts List .........................................................................................6-1

6.2 Front Cover Assembly .........................................................................................6-2

6.2.1 Exploded View .........................................................................................6-2

6.2.2 Front Cover Assembly Parts List .............................................................6-3

6.3 Pump Module Assembly ......................................................................................6-4

6.3.1 Exploded View .........................................................................................6-4

6.3.2 Pump Module Assembly Parts List .........................................................6-5

6.4 Rear Cover Assembly ..........................................................................................6-6

6.4.1 Exploded View .........................................................................................6-6

6.4.2 Rear Cover Assembly Parts List .............................................................6-6

6.5 Others ..................................................................................................................6-7

6.5.1 Others Parts List ......................................................................................6-7

7 Upgrade .................................................................................................................7-1

7.1 Tools ....................................................................................................................7-1

7.2 Software Upgrade ...............................................................................................7-1

7.2.1 Software Burning Method ........................................................................7-1

7.3 Brand Library Download ......................................................................................7-5

Summary of Contents for BeneFusion SP3

















































































Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands

Mindray BeneFusion SP3, Service Manual

Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands