Mindray BeneFusion SP3 Service Manual Download

Page: 44 / 80

4-8

Equipment Fault

Failure

Description

Possible Cause

Handling Method

In case that no

external power is

connected, there

is no display

upon startup, the

battery LED is

not on and the

buzzer does not

sound.

1.The battery is dead.

2.Poor battery connection.

3.The motor is faulty.

4.Poor contact between the

keypad board and the control

board.

5.The keypad board is faulty.

6.The control board is faulty.

1.Try to connect to an external

power source for charging.

2.Reconnect the battery.

3.Replace the battery with a new

one.

4.Reconnect the keypad board

and the control board.

5.Replace the keypad board.

6.Replace the control board.

In case that no

external power is

connected, there

is no display

upon startup, the

battery LED is

on and the

buzzer sounds.

1.Poor contact between the

keypad board and the control

board.

2.The LCD FPC is poorly

connected.

3.The LCD is faulty.

4.The keypad board is faulty.

5.The control board is faulty.

1.Reconnect the keypad board

and the control board.

2.Reconnect the LCD FPC.

3.Replace the LCD.

4.Replace the keypad board.

5.Replace the control board.

The equipment

is powered on

normally, but the

screen is black,

white or blurred.

1.Poor contact between the

keypad board and the control

board.

2.The LCD FPC is poorly

connected.

3.The LCD is faulty.

4.The keypad board is faulty.

5.The control board is faulty.

1.Reconnect the keypad board

and the control board.

2.Reconnect the LCD FPC.

3.Replace the LCD.

4.Replace the keypad board.

5.Replace the control board.

The external AC

is connected, but

the AC LED is

not on.

1.Poor contact or damaged AC

power cord.

2.Poor contact in the AC-DC

internal connection line.

3.Poor contact between the

keypad board and the control

board.

4.AC-DC module failure.

1.Reconnect or replace the AC

power cord.

2.Reconnect the AC-DC internal

connection line.

3.Reconnect the keypad board

and the control board.

4.Replace the AC-DC module.

Unable to charge

effectively

1.Poor battery connection.

2.The motor is faulty.

3.The control board is faulty.

1.Reconnect the battery.

2.Replace the battery.

3.Replace the control board.

Error in the

displayed text or

image

Software version or resource file

is burnt incorrectly.

Re-burn the software version or

resource file.

Summary of Contents for BeneFusion SP3

















































































Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands

Mindray BeneFusion SP3, Service Manual

Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands