Mindray BeneFusion SP3 Service Manual Download

Page: 57 / 80

5-11

3. As shown in the figure: Remove the hot melt adhesive on the clips (Note: if it is

difficult to remove, drip a drop of alcohol. Then you can remove it easily), release the

clips, pull out the FPC wire, tear the sponge pad, and then loosen the three M3X8

Phillips pan head screws that fix the PCBA. Finally remove PCBA from the pump

body.

4. As shown in the figure: Use a needle-nosed pliers to remove the collar on the

transition gear shaft and remove the transition gear from the pump body assembly.

5. As shown in the figure: Remove the five M3x12 Phillips pan head screws on the

pressure sensor holder with the Phillips screwdriver in the order shown in the figure.

Then remove the holder bracket and bearing.

Note: You should still follow the screw locking sequence as shown during assembly.

Tear the sponge pad

Pull out the

FPC wire

Transition Gear

Summary of Contents for BeneFusion SP3

















































































Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands

Mindray BeneFusion SP3, Service Manual

Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands